Replacement Angled Mounting Grommet for Optronics AL91PB Side Marker Light on Skeeter Trailer

Question

Question:

I have a Skeeter trailer for a WX2060. The side marker lights, Optronics AL91PB, are mounted in a rubber grommet that has an angle of about 33-35 degrees. Can you supply this rubber grommet?

asked by: Edward K

0

Expert Reply:

Hi Edward, great question.

The grommet you need for your Optronics AL91PB light is the Mounting Grommet with Built in Wedge for A91 or AL91 Series Lights, part # A91GZB. This is the angled style grommet designed for the A91 and AL91 series lights, so it is the correct match for your AL91PB light as well. The built in wedge helps the light sit flush on angled mounting surfaces like the ones commonly found on Skeeter trailers.

Where do you like to take your WX2060? What kind of fishing do you do?

expert reply by: Heather A

0

Edward K.

5/27/2026

Thank you for the quick response! Lake Erie trolling for walleyes and 1000 Islands for northern pike, smallmouth bass, and largemouth bass.

Matt

5/28/2026

Like Erik stated I purchased these from E trailer for my Skeeter bass boat easy loader trailer and fit perfectly. I used a flathead screwdriver to gently seat the grommet into the frame of the trailer fits nice and snug, good to go.

Erik

5/28/2026

The grommets are a perfect fit for a skeeter trailer. Bought them for a friend and we’re exactly what was there before

Heather A.

5/29/2026

@Erik Thank you for confirming! It's always nice to hear from someone that has used the product. What kind of fishing do you do?

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Replacement Angled Mounting Grommet for Optronics AL91PB Side Marker Light on Skeeter Trailer

Product Page this Question was Asked From

Continue Researching