Looking for TImbren Front Suspension Kit # DF25004F for 2023 Ram 3500

Question

Question:

Timbren SES DF25004F, I was looking for this item but it showed only T98GR. But when I checked that part on Timbren site that part did not exist. would you please let me know what the difference is.or if it is the same. Like I said the rear part is the same on both sites but the front is the difference.

asked by: Ronald G

0

Expert Reply:

Hey Ronald, our part number # T98GR is the same as the Timbren part number DF25004F so if you order the # T98GR that is what you'd get from us. This is the correct Timbren front kit designed for your 2023 Ram 3500 as well. Are you running a plow setup?

expert reply by: Jameson C

0

Ronald G.

11/17/2025

Hi thanks for getting back to me , I don’t have a plow yet but was putting these on the front and rear for the extra weight that I have at times

Reply

Jameson C.

11/17/2025

@RonaldG Makes sense!

Reply

Answer 1

Hey Micah! Pacbrake has actually been around for a long time, more than 60 years. We have had customers ask for these air bags in the past, and we've seen them on vehicles coming in. Until now, Firestone has been the go to since their quality is…

view full answer...

Answer 2

Hey Ronald, our part number #T98GR is the same as the Timbren part number DF25004F so if you order the #T98GR that is what you'd get from us. This is the correct Timbren front kit designed for your 2023 Ram 3500 as well. Are you running a plow…

view full answer...

Answer 3

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hey Jeff, I checked with Firestone and the only version of the 2025 Toyota Tacoma that the part #F83VV doesn't fit is the 2 wheel drive models. The SR5 can be either 4wd or 2wd so you would need to verify which configuration you have to know if…

view full answer...

Answer 9

Hey Todd! At the lowest setting, the saddle of the Power Mountain Tallboy Off-Road Bottle Jack #PM34FR sits at 14" and the top of the saddle arms are at 15-3/8". I took a photo of it out in our warehouse, and while I wasn't able to get…

view full answer...

Answer 10

The Timbren kit #TFR250SDJ does not require a mounting plate above the axle as it is designed to contact the round the plate that is currently on the axle that is mounted below the spring pack. I would recommend sticking with this kit even though you…

view full answer...

Answer 11

Hey Kurt, yes the correct gap for SumoSprings Solo kits like the part #SS88UV is 1/2 inch to 1 inch like you mentioned. Did you install this already?

view full answer...

Answer 12

Hey Bill, yes the Furrion Vision S+ #FR64AD would be a direct replacement for your current Vision S system. None of it is backwards compatible with the standard Vision S system though.

view full answer...

Looking for TImbren Front Suspension Kit # DF25004F for 2023 Ram 3500

Product Page this Question was Asked From

Continue Researching