Recommended Hitch for a 2002 Chevy S-10

Question

Question:

I need a replacement Reese Hitch for my 2002 Chevy S-10. Them ones on your site do not look the same.

asked by: Jamie P

0

Expert Reply:

Hey Jamie. Reese was bought out by Draw-Tite awhile back so their hitch for a 2002 Chevy S-10 is item # 75085. It's a bit backordered but I do have an identical alternative.

For your 2002 Chevy S-10, I recommend the Curt Hitch item # C13021. This hitch is custom fit and bolts to your S-10 with included hardware. It is a class III hitch with a 2" receiver.

I have attached a picture of it below so you can see what it looks like when installed. If you have any additional questions go ahead and throw them into the comment box below.

expert reply by: Jerred H

0

Curt Hitch item # C13021
(click to enlarge)

Jerred H.

9/12/2025

Hey Jamie, did the Curt Hitch work out for your 2002 Chevy S-10? I'm asking because it could help others who are looking for a similar solution.

Answer 1

I spoke with my contact at Draw-Tite, who tells me that the Class III #75085 receiver will fit the 1999 S-10 Sportside with the non-towing bumper. He did not have any information regarding fit on the Extreme model, which means that some trimming of…

view full answer...

Answer 2

On a trailer hitch receiver, concealed means the crosstube does not show at the rear of the truck, just the receiver does; while exposed means the crosstube and the receiver show. A lot of people really like the concealed crosstube because it keeps…

view full answer...

Answer 3

For your 2000 GMC Sonoma 4x4, the Draw-Tite Max-Frame Trailer Hitch Receiver #75085 is a confirmed fit for the Sportside with non-towing bumper as well as the Factory Step bumper. It is not a fit for the ZR2 models or the Factory Roll Pan bumper. It…

view full answer...

Answer 4

If you have a factory step bumper or your 1996 S-10 is the ZR2 model, the trailer hitch I recommend is part #75051. If you have a Sportside with a non-towing bumper, the hitch I recommend is part #75085. These are Class lll hitches and they have…

view full answer...

Answer 5

The Curt Class III hitch you'd looked at, part #C13021 is indeed a fit for the 2002 GMC Sonoma with the factory step bumper, as shown in the provide photo. If you'll be using the hitch for towing, you can install a 4-pole trailer connector…

view full answer...

Answer 6

To determine if a trailer hitch receiver will fit on your 2003 Chevrolet S-10 that has an aftermarket bumper you'll have to do a little measuring. There are three Curt Class III trailer hitch receivers that may work for you. You'll need to…

view full answer...

Answer 7

Though the Curt # C13409 and Draw-Tite #76271 are nearly identical to each other, there are a few subtle differences. First being where they sit once installed. The will both have the exact same height of 14-1/2 inches, but the Draw-Tite #76271 will…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Thank you for the photo; it looks like your 1997 Chevy S-10 is the Sportside with non-towing bumper and the trailer hitch that fits is the Draw-Tite #75085. This is a Class III hitch that is a complete bolt-on installation so no drilling into your…

view full answer...

Answer 10

The correct hitch will depend on which bumper your S-10 is equipped with. For a factory step bumper, I'd recommend the Curt #C13132. For a roll pan bumper, you'll want to use #13920, but you'll need to cut a hole in the license plate well…

view full answer...

Answer 11

A great majority of standard ball mounts are designed so that they can be used in either the drop or rise position. Using a ball mount like the Draw-Tite #2753 that you were looking at in the rise position is just a matter of turning it upside down…

view full answer...

Answer 12

For your 2001 Chevy S-10 with the factory step bumper what you would need is the Curt hitch part #C13021 which is a confirmed fit for your truck and it's configuration. The #C19031 that you referenced is a universal install hitch that isn't…

view full answer...

Recommended Hitch for a 2002 Chevy S-10

Products Featured in This Question

Continue Researching