Do All Trailer Jack Use the Same Bolt Pattern? Do You have an Electric Jack for My 2015 Jayco?

Question

Question:

I have a 2015 Jayco 23 MBH trailer. The Electric tounge jack doesnt work. Is the bolt pattern for all electric tounge jacks the same?

asked by: J D

0

Expert Reply:

Hello JD,

Most of the electric trailer jacks use a 3 bolt design, 3" spacing. I looked up the specs on your 2015 Jayco 23 MBH trailer and I see the tongue weight is 480–520 lbs, I recommend our etrailer Electric Trailer Jack - A-Frame - 18" Lift - 3,500 lbs # e23ZV. It's the only jack we carry with a Limited Lifetime Warranty. It even comes with a nice bag to keep over the top to keep it protected from those harsh elements, and a manual hand crank for if you were to ever need it.

Any big trip planned for the near future? If so, where are you headed?

expert reply by: Kate F

0

All parts included with etrailer electric jack.
(click to enlarge)

Answer 1

Hello. The etrailer Electric Trailer Jacks #e55ZV and #e23ZV do have a manual backup option. You just remove the rubber cap on top of the housing and you can use the included manual crank to raise/lower the jack. Take a look at the picture below and…

view full answer...

Answer 2

I have provided a picture that shows the jack dimensions. These measurements were taken here by another Expert recently. The outer tube is 2 inches in diameter and the inner tube is 1-3/4 inches in diameter. The bracket to mount the jack uses a…

view full answer...

Answer 3

Hey Bobby, thanks for reaching out. The etrailer Electric Trailer Jacks #e23ZV and #e55ZV do indeed have a worklight built in. Take a look at the picture below. There is not a separate wire for the light. As long as you connect the red wire to 12v…

view full answer...

Answer 4

Hello Kyle, Yes, our etrailer Electric Trailer Jack - A-Frame - 18" Lift - 3,500 lbs #e23ZV would be an excellent fit for your 2-horse trailer at 3,000 pounds. A 4-flat trailer connector only carries lighting functions (tail, turn, brake, and…

view full answer...

Answer 5

Hello Ralph, thanks for reaching out. The etrailer Electric Trailer Jack #e23ZV will be a great option for you. The jack can be rotated to the side if needed. We have one of these jacks on our trailer here at the shop and I have seen it rotated and…

view full answer...

Answer 6

Since your 2020 Ford Ranger SXT came with a factory installed 7-way trailer connector, you should have a brake controller connector under the dash. That being said, the connector that would most likely fit #3034-P, has not been confirmed as a fit for…

view full answer...

Answer 7

Hello Marc, For the Lippert Model 181794 you are going to want the Replacement Top Cover for Lippert Electric Trailer Jack #LC285160, Replacement Bottom Jack Cover with Light Lens #LC23UD, and for rubber plug Replacement Override Plugs #LC733924. I…

view full answer...

Answer 8

Hey Reginald, We do in fact have the manual for that jack! I am getting it added to the website but will go ahead and attach and image of it for you below. Was there anything specific you were wanting to know about the jack?

view full answer...

Answer 9

Sounds like the jack has been damaged enough that it's time to replace it. Powered jacks have a screw that turns inside a threaded shaft that allow the jack to rise and lower. It sounds like that shaft has broken away from the rest of the jack…

view full answer...

Answer 10

Hello Izzy, thanks for reaching out. The necessary installation hardware will be included with the etrailer Electric Trailer Jacks like parts #e55ZV and #e23ZV. You can see the hardware pictured below. It is just 3 bolts that hold the A-frame jack to…

view full answer...

Answer 11

Hello Brian, thanks for reaching out. That would be fine. There is really no need for a cut-off switch here but there is no reason why you can't use one. As long as the jack is connected to a 12v power source, it will operate as intended.

view full answer...

Answer 12

Hey Geoff! How do you like it so far? The wire on the #e23ZV is 12 gauge. You can add a fuse if you want but it isn't necessary since the jack has a 20A automatic reset fuse built in already. If you want to add one I would make it the same 20A.

view full answer...

Do All Trailer Jack Use the Same Bolt Pattern? Do You have an Electric Jack for My 2015 Jayco?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching