What is Height Range of Malone Axis Truck Bed Load Extender # MPG907
Updated 10/27/2025 | Published 03/19/2025
Question:
Regarding the Malone MPG907 truck bed extender: Your website Specs say that in the horizontal position, the height from the inside top edge of the receiver, to the top of the crossbar is Lowest position 15inch and Highest position 22 The measurements shown in a graphic at Maloneautoracks.com for this same model show from top edge of the bar that goes into the receiver which would be the same as saying the inside top edge of receiver to top of the crossbar of Lowest position 13inch and Highest position 20 Is the wording of your specs wrong and should instead say measured from the inside bottom edge of the receiver? If so, that change would make both of the described measurements be in agreement, when considering the receivers 2inch square size. To fit my situation, I need to know for sure what the correct measurement size is. I also need to verify, does each side wing already contain two holes so that the optional roller can easily be added at a later time? Thanks for your assistance.
asked by: Rick J
Expert Reply:
Hey Rick, I can't speak for Malone but we measured from the top of the hitch opening to the top of the Malone Axis part # MPG907 and found the height range to be between 15 and 22 inch. I also made sure that when we took this measurement it was the most current version of this rack as it has been updated over the years.
Product Page this Question was Asked From
Malone Axis Truck Bed and Roof Load Extender for 2" Hitches - 375 lbs
- Truck Bed Extender
- Bed Extension
- Roof Extension
- Adjustable Height
- 375 lbs
- Adjustable Width
- Hitch Mount
- Steel
- Malone
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: truck bed extender
- Search Results: trailer hitch
- Search Results: receiver
- Shop: Malone Axis Truck Bed and Roof Load Extender for 2" Hitches - 375 lbs
- Shop: Trailer Wiring
- Video: Malone Axis Truck Bed and Roof Load Extender Comprehensive Review
- Shop: Malone Axis Truck Bed and Roof Load Extender with Load Roller - 2" Hitches - 375 lbs
- Shop: Trailer Hitch
- Search Results: custom fit vehicle wiring
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: hitch receiver
- Q&A: Can a Load Extender be Used to Carry Kayaks Out of an SUVs Hatch
- Video: Mount: Malone Axis Truck Bed and Roof Load Extender for 2" Hitches on a 2022 Toyota Tundra
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: Recommended Bed Extender for Carrying Two Kayaks w/ a Short Bed Truck
- Shop: Flint Hill Goods Truck Bed Extender - 2" Hitches - 350 lbs
- Shop: Malone Safety Flag - 12" Wide x 12" Long
- Shop: Front Mount Hitch
- Video: Review of TowSmart Trailer Hitch - Custom Fit Hitch - TS63ZR
- Video: How to Install the Curt Trailer Hitch Receiver on a 2020 Jeep Gladiator
- Video: Malone Axis Truck Bed and Roof Load Extender for 2" Hitches Review
- Q&A: Diameter and Weight Capacity of Malone Truck Bed Extender Roller # MAL52VR
- Q&A: Recommended Truck Bed and Roof Load Extender for a 2" Hitch
- Q&A: Can Yakima LongArm Extender be Used for Long Kayak and 5-1/2 Foot Bed Truck
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
on Truck Bed Extender
Jameson C.
10/27/2025
Hey Rick, how did those 15- to 22-inch measurements work out for your setup with the Malone Axis bed extender? Your update could make it easier for others trying to confirm the same fit.