Is There a 7-Way Extension For Truck Camper to Truck

Question

Question:

Hi, I just bought a 2003 Eagle Cap slide in camper. The 7 pin cord coming out of the camper is too short to reach the back of my trucks 7 pin connecting point. I was wondering if you have an extension the could connect to the camper cord and back to the truck connector? Thanks Charles Cisco

asked by: Charles C

0

Expert Reply:

Hi Charles,

Yes, we have connectors that go from the 7-way on your camper to the 7-way on your truck; you can use either the 10 foot long TorkLift Wiring Harness Extension # TLW6510 or Curt 7 foot long # C56080.

The Curt says it is 5th wheel/gooseneck but it's the exact same thing, just a 7-way to 7-way extension.

expert reply by: Kyle S

0

Lazer S.

1/19/2026

Hey Charles, how did the wiring extension work out for connecting your camper to the truck? Your results could really help others trying to bridge a short 7-way cord on their setup.

Answer 1

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 4

This is a great choice Joe and thanks for reaching out! Weigh Safe True Tow Weight Distribution Hitch #WS49MR would be a good match for your setup. Since your Grand Design toy hauler will have a loaded tongue weight between 1,300 and 1,600 lbs, this…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Hey Doug. So long as your Husky 5th wheel hitch isn't three decades old you shouldn't have any issues attaching it to the B&W Custom Installation Kit w/ Base Rails item #BWRVK2402. Most 5th wheel hitches for the last 20 years have used…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 9

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 10

Hey Ken! Instead of worrying about fitment and a potential return I can give you some measurements so you can figure it out before ordering. The standard shank on the B&W Continuum Weight Distribution System #BW28FR is 11-3/8" from the…

view full answer...

Answer 11

Hey Kyle. Unless you're driving around with 1,500 lbs of gear in the bed of your 2025 Ford F-250, the Air Lift LoadLifter 5000 Ultimate Air Helper Springs item #AL29DQ are not going to be overloaded. Your 5th wheel hitch and a full tank of fuel…

view full answer...

Answer 12

Hey Brady, Brophy in the past has told us that the tie downs part #HSWB don't have a weight capacity but you would want to make sure you use them only with campers that were designed to fit the bed length of the truck. The turnbuckles part #TDHP…

view full answer...

Is There a 7-Way Extension For Truck Camper to Truck

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching