Mounting Plate Bolt Spacing For Dutton-Lainson Boat Trailer Jack DL22335
Updated 01/19/2026 | Published 08/08/2024
Question:
I need to replace a tounge jack on my 2004 ranger trail trailer. It is bolted on. I would like to know if you have the dimensions for the bolt spacing for the mounting plate. I’d like to find a direct bolt on.
asked by: Justin F
Expert Reply:
Hello Justin. The mounting plate on the Dutton-Lainson Boat Trailer Jack # DL22335 has 7/16" holes. They are 5-1/2" apart across. There is 2-3/8" between the top hole and the hole under it. Then there is 1" separating the lowermost holes. All of these measurements are taken center hole to center hole.
This will fit your trailer frame as long as it does not exceed 3" wide by 5" tall. I have a picture of the dimensions below, but with the bracket flipped on its side. I hope this helps.
(click to enlarge)
Product Page this Question was Asked From
Dutton-Lainson Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 12" Lift - 1,500 lbs
- Trailer Jack
- Boat Trailer
- Enclosed Trailer
- Utility Trailer
- Side-Mount Jacks
- Swivel Jacks
- Sidewind Jack
- 1001 - 2000 lbs
- Manual Jack
- 12 Inch Lift
- Bolt-On
- With Wheel
- Dutton-Lainson
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: boat trailer jack
- Search Results: trailer jack
- Q&A: Mounting Bracket Bolt Hole Dimensions Fulton Trailer Jack # F87CR
- Q&A: Bracket Mounting Hole Dimensions of Fulton Jack part # F27CR
- Q&A: Difference Between Snap Ring and Bolt On Boat Trailer Jacks
- Shop: Dutton-Lainson Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - 1,500 lbs
- Shop: Dutton-Lainson Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 12" Lift - 1,500 lbs
- Shop: etrailer Boat Trailer Jack w/ Dual Wheel - Sidewind - Swivel - 10-3/8" Lift - 1,500 lbs
- Q&A: Left to Right Hole Dimensions of Fulton XLT Bolt-Thru Swivel Trailer Jack
- Q&A: 1995 Freedom Wheels Cobalt 220 Runabout Replacement Trailer Jack Recommendation
- Q&A: Dimensions for Fulton Bolt-Thru Swivel Marine Jack # FXPD15L
- Q&A: Compatibility of Fulton F141132 XLT Trailer Jack With Weld-On Mount for Existing Jack
- Video: A Look at the Power Mountain Tallboy 6 Ton Off-Road Bottle Jack with a Military Cargo Trailer
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Search Results: trailer tires and wheels
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Feature Review - Big Truck Big RV Trailer Jack Foot Scale with Tongue Weight Gauge
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Video: Review of Power Mountain Automotive Tools - Jacks and Jack Stands - PM34FR
- Shop: Suspension Enhancement
- Search Results: trailer wiring
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Article: How to Measure for Trailer Hitch Drop
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Video: A Closer Look at the etrailer Sidewind Aluminum Jack
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Shop: Brake Controller
on Trailer Jack
Jesse M.
1/19/2026
Hey Justin, did the Dutton-Lainson boat trailer jack line up with the bolt spacing on your Ranger Trail trailer? Knowing how the fit turned out could really help others looking for a direct bolt-on replacement.