Dimensions for Fulton Bolt-Thru Swivel Marine Jack # FXPD15L

Question

Question:

Thanks Chris, Can you give me the offset to the tube centre from the mounting plate surface. I’m assuming it swivels from the centre of the bracket.

asked by: Alan T

1

Helpful Expert Reply:

I wasn't able to get a CAD drawing for the Fulton Bolt-Thru Swivel Marine Jack # FXPD15L that you referenced (manufacturer's don't typically make those available), however I did go out to our warehouse to take a few measurements on the jack.

This swivel jack features an overall retracted height of right at 26 inches. From the bottom of the wheels to the center of the mounting bracket there is a length of 12 inches. It has an outer tube diameter of 2-1/4 inches and the bracket itself measures 6-1/4 inches wide and 6 inches tall.

I have attached an image with these and some additional dimensions labeled that you can take a look at. If you need any other dimensions, please let me know and I will be happy to take them for you.

expert reply by: Chris R

1

click to enlarge

Alan T.

7/18/2018

Thanks Chris, Can you give me the offset to the tube centre from the mounting plate surface. I’m assuming it swivels from the centre of the bracket.

Reply

Chris R.

7/18/2018

I went back out to the warehouse and measured a distance of 2-1/2 inches from the center of the outer tube to the inside of the mounting bracket. From the center of the tube to the outside of the bracket there is a distance of 3-1/2 inches. I have attached an image to assist.

Reply

Luke

6/15/2020

Will this fit a 5” trailer frame?

Reply

Chris R.

6/19/2020

The Fulton # FXPD15L does come with a bracket that will allow it to fit 3" x 5" trailer frames.

Reply

Answer 1

A dual wheel trailer jack like the Fulton part #FXPD15L would be your best option as it has the capacity you need and since it has two wheels it would roll a little easier.

view full answer...

Answer 2

One option is to use a rack and gear jack for A-frame trailers, #BD165412. But in order to get a retracted height under 6 inches the wheel would have to come off. This is because the retracted height is 7-1/2 inches. There are other A-frame jacks to…

view full answer...

Answer 3

Thanks for sending me your picture; it helped out a lot! Instead of new U-bolts, I would instead suggest the Fulton replacement mounting hardware #F500286. This will be able to accommodate different sized frames of trailers and the threads will be…

view full answer...

Answer 4

The #F500349 Replacement Bolt-On Mounting Kit for Fulton XP Series Jacks comes with a single bolt, nut and washer for the center attachment point. There are no U-bolts included in this kit. If you are looking for the mounting hardware used with the…

view full answer...

Answer 5

The only repair kit we have for your Profile 2000 hand winch is the Winch Ratchet Repair Kit by Dutton-Lainson item #DL70475. If this isn't what you are needing you will have to replace your winch. I recommend the Dutton-Lainson Hand Winch -…

view full answer...

Answer 6

It might be possible to repair the winch you have currently but without knowing what winch you have it's really pretty hard for me to say if that's possible or not. Most likely it's time for an all new winch like the Dutton Lainson part…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Dimensions for Fulton Bolt-Thru Swivel Marine Jack # FXPD15L

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching