What Is the Bolt Pattern Dimensions of the Dutton-Lainson DLx-P Round Swivel Jack

Question

Question:

hello. What is the distance from the top holes on the mounting plate to each of the bottom holes. Also, what diameter are the bolts? Thanks so much!

asked by: Lisa J

1

Helpful Expert Reply:

The mounting plate on the Dutton-Lainson Round Swivel Jack part # DL22335 has bolt holes which are 7/16" diameter. The bolt holes are spaced 5-1/2" apart on center from top to bottom and then in 1" increments apart working your way from the bottom to the top. If your trailer frame does not exceed 3" wide x 5" tall then the jack will bolt right on.

expert reply by: Conner L

1

Answer 1

Yes Brad, that absolutely makes sense. There’s a good chance you can reuse the Dutton-Lainson welded swivel mount already on your Boatmate trailer. The Dutton-Lainson #DL22339 uses a standard swivel-mount design, I attached a photo of the mounting…

view full answer...

Answer 2

Hello Nick, thanks for reaching out. The Dutton-Lainson Boat Trailer Jack #DL22335 may work for you. It has 7/16" holes. They are 5-1/2" apart across. There is 2-3/8" between the top hole and the hole under it. Then there is 1"…

view full answer...

Answer 3

Replacement Mounting Hardware for etrailer and Ram Swivel Marine Jacks - 1,200 lbs and 1,500 lbs Item #MJ-1000B-MBB will actually be perfect for you. I checked the specs on the actual jacks that come with this hardware and it is basically identical…

view full answer...

Answer 4

Hey Guy, so the mounting bracket of the Fulton Jack part #F87CR allows it to fit on a trailer frame that is up to 5 inches tall and 3 inches wide. So that means that from inside to inside on the outer most bolt holes the height is 5 inches but from…

view full answer...

Answer 5

Hey James, I attached a picture that shows all of the dimensions of the mounting holes that are on the Fulton trailer jack part #F27CR that you referenced.

view full answer...

Answer 6

A boat trailer jack that uses a snap ring works differently than one that is a bolt-on, like yours, because the mounting bracket for a bolt-on jack and snap-ring jack will be different. Because you have a Fulton 1,200 lb bolt-on jack, I assume your…

view full answer...

Answer 7

The trailer jacks we offer that are similar to the #FTJ120W0301 you came from all use a mounting plate that has different dimensions than what you said your trailer jack plate has. You can remove the welded mounting plate on your trailer and have a…

view full answer...

Answer 8

The 3-bolt mounting flange on the Lippert Electric A-Frame Trailer Jack #LC285318 has a standardized hole pattern. This jack is intended to mount so that the included LED light faces forward toward the tow vehicle to illuminate the coupler and hitch…

view full answer...

Answer 9

I went out to the warehouse and pulled one of the Pro Series Snap-Ring Swivel Jacks, #PSEJ10000101, to measure for you. I added dimensions to a photo I took of the mounting plate for you to use to see if the mounting pattern will match up to your…

view full answer...

Answer 10

Yes. The bolt patterns that were referred to in the videos are actually the same and in reality the .06" is a negligible difference that falls within a reasonable margin of error; I believe that on the #F1413050334 measurements were performed…

view full answer...

Answer 11

The mounting holes for the mounting bracket of the Fulton F2 Jack part #F1413140334 measure 5-1/2 inches apart vertically and 4-1/2 inches horizontally.

view full answer...

Answer 12

Without knowing the part number and manufacturer of your current trailer jack, I couldn't speak to the compatibility of the mounting plate for your current jack with the mount that the Fulton #F141132 XLT uses. The #P9012-00 weld-on mount for the…

view full answer...

What Is the Bolt Pattern Dimensions of the Dutton-Lainson DLx-P Round Swivel Jack

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching