Snap Ring Swivel Jack for a Trailer that Already has a Jack Mount
Updated 06/04/2020 | Published 06/22/2018
Products Featured in This Question
Question:
My trailer already has a welded-on snap-ring style mount with 1/2inch pin holes and a 2 1/2inch snap ring. Can I use this jack directly onto my mount? Thanks.
asked by: Tracy B
1
Helpful Expert Reply:
Jack # DL22210 isn't a snap ring jack but we do have other options that will likely work with your existing mount such as # FTJ120W0301. The hole spacing for the pull pin is 3 inches apart on center. I have linked a video review of this jack for you.
expert reply by:
Michael H
1
click to enlarge
Product Page this Question was Asked From
Dutton-Lainson Boat Trailer Jack w/ Wheel - Sidewind - 12" Lift - 1,500 lbs
- Trailer Jack
- Boat Trailer
- Utility Trailer
- Side-Mount Jacks
- Sidewind Jack
- 1001 - 2000 lbs
- Manual Jack
- 12 Inch Lift
- Bolt-On
- With Wheel
- Dutton-Lainson
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: dexter surge brake actuator
- Search Results: a60 actuator
- Search Results: trailer lights
- Search Results: stoltz
- Search Results: dexter brake actuator
- Q&A: Looking For Replacement Tail Lights For 2003 Ranger Bass Boat 519VX Trailer
- Q&A: LED Trailer Taillight Kit Recommendation for 2000 Ranger Boat Trailer
- Search Results: hydraulic brake lines
- Search Results: 5 flat trailer wiring
- Shop: Fulton Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - Zinc - 1.2K
- Shop: Replacement Inner Member for Dexter DX7.5L Actuator - Tandem Axle w/ Disc - 2" Ball - 7,500 lbs
- Shop: Dutton-Lainson Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 12" Lift - 1,500 lbs
- Shop: Dutton-Lainson Boat Trailer Jack w/ Wheel - Sidewind - 12" Lift - 1,500 lbs
- Shop: Trailer Wiring
- Shop: etrailer Electric Trailer Brakes - 7" - Left/Right Hand Assemblies - 2,000 lbs
- Shop: Kodiak Hydraulic Brake Line Kit - Tandem Axle - 15'
- Shop: Right Angle 3-Wire Pigtail for Optronics Trailer Lights - 3-Prong PL-3 Plug - 10" Lead
- Video: Complete Breakdown of the Fulton Boat Trailer Jack w/ Wheel
- Q&A: Replacement Jack for Bulldog Model 130 Marine Jack
- Q&A: Replacement for Dutton-Lainson 203925B 1000 lb Capacity Swivel Trailer Jack
- Article: Best Boat Trailer Jacks
- Video: In-Depth Review of the Fulton Boat Trailer Jack w/ Wheel
- Q&A: Cost Effective Weld-On Trailer Jack With A Wheel
- Q&A: Handle Diameter and Length to Fit etrailer.com Sidewind Jack Handle with Haul Master Trailer Jack
- Q&A: Is there a Higher Rated Fulton Jack that Uses the Same Swivel Mount as My TJ120W0301?
- Video: Let’s Check Out the Replacement Sidewind Handle for etrailer and Ram Swivel Marine Jacks
- Video: Rebuilding Your Trailer Jack
- Video: Complete Breakdown of the Replacement Cap for etrailer and Ram Swivel Marine Jacks
- Video: Breaking Down the Replacement Sidewind Handle for etrailer and Ram Swivel Marine Jacks
- Video: Comprehensive Review: Dutton-Lainson Boat Trailer Jack w/ Wheel
Michael T.
6/4/2020
Just wanted to let you know that I just replaced my fulton factory jack with a independent caster, mounted on a weld on bulldog mount Part #P20520-00 on my 1997 javelin /EZ-Drive trailer. I found a Dutton-Lainson DLx Part#22210. By removing the swivel adapter from the jack, the mounting plate is a exact fit to the old Fulton system. It will go on the bulldog snap ring mount perfectly. The older pin lock on my mount was 3/8", but was easily drilled to 1/2".