Left to Right Hole Dimensions of Fulton XLT Bolt-Thru Swivel Trailer Jack

Question

Question:

For Fulton 141133, what is the distance between the mounting holes - horizontal dimension not listed on photo

asked by: Earl M

0

Expert Reply:

The mounting holes on the Fulton XLT Bolt-Thru Swivel Trailer Jack part # F141133 are spaced 5-1/2" apart left to right as you can see in the attached photo.

expert reply by: Conner L

0

Left to Right Hole Dimensions of Fulton XLT Bolt-Thru Swivel Trailer Jack
(click to enlarge)

Answer 1

The Fulton mount #F500276 hole to hole length center on center is 5-1/2 inches and the hole to hole width center on center is 4-1/2 inches. The overall is 6 by 5 inches. The bolts included are 7/8" with threads that are 16 course.

view full answer...

Answer 2

The Fulton Bolt-Through Swivel Jack, part #F1411300301 will allow you to use the existing bracket welded to your trailer frame. The jack has a 1500 lb lift capacity, so if your trailer's tongue weight is less than that amount, it'll work…

view full answer...

Answer 3

The only trailer jack that will work with your existing mounting bracket and not contact the boat with a full rotation of the handle is the Fulton Bolt-Thru Swivel Marine Jack part #F1411300301. I understand this does not have the sharkskin coating…

view full answer...

Answer 4

Hello Jim, The Fulton Boat Trailer Jack w/ Wheel - Sidewind - Swivel - 10" Lift - Zinc - 1.2K #FTJ120W0301 is rated for 1,200 pounds. Keep in mind that this rating applies to the tongue weight of the trailer, not the overall trailer weight. For…

view full answer...

Answer 5

Without knowing the part number and manufacturer of your current trailer jack, I couldn't speak to the compatibility of the mounting plate for your current jack with the mount that the Fulton #F141132 XLT uses. The #P9012-00 weld-on mount for the…

view full answer...

Answer 6

A boat trailer jack that uses a snap ring works differently than one that is a bolt-on, like yours, because the mounting bracket for a bolt-on jack and snap-ring jack will be different. Because you have a Fulton 1,200 lb bolt-on jack, I assume your…

view full answer...

Answer 7

Hey Guy, so the mounting bracket of the Fulton Jack part #F87CR allows it to fit on a trailer frame that is up to 5 inches tall and 3 inches wide. So that means that from inside to inside on the outer most bolt holes the height is 5 inches but from…

view full answer...

Answer 8

Hey James, I attached a picture that shows all of the dimensions of the mounting holes that are on the Fulton trailer jack part #F27CR that you referenced.

view full answer...

Answer 9

The mounting plate on the Dutton-Lainson Round Swivel Jack part #DL22335 has bolt holes which are 7/16" diameter. The bolt holes are spaced 5-1/2" apart on center from top to bottom and then in 1" increments apart working your way from…

view full answer...

Answer 10

Yes. The bolt patterns that were referred to in the videos are actually the same and in reality the .06" is a negligible difference that falls within a reasonable margin of error; I believe that on the #F1413050334 measurements were performed…

view full answer...

Answer 11

Hello Justin. The mounting plate on the Dutton-Lainson Boat Trailer Jack #DL22335 has 7/16" holes. They are 5-1/2" apart across. There is 2-3/8" between the top hole and the hole under it. Then there is 1" separating the lowermost…

view full answer...

Answer 12

The trailer jacks we offer that are similar to the #FTJ120W0301 you came from all use a mounting plate that has different dimensions than what you said your trailer jack plate has. You can remove the welded mounting plate on your trailer and have a…

view full answer...

Left to Right Hole Dimensions of Fulton XLT Bolt-Thru Swivel Trailer Jack

Continue Researching