How To Install A Trailer Hitch When The Vehicles Factory Weld Nuts Are Ruined
Updated 07/30/2024 | Published 07/27/2024
Products Featured in This Question
Question:
The factory holes in my 4runner frame are ruined. Is it safe to drill new bolt holes in the Curtis Hitch and frame and mount the hitch in that fashion?
asked by: Christopher T
Expert Reply:
Hello Christopher. Broken weldnuts in the frame can definitely be a pain, but it is still possible to install the 13445 hitch on your 4Runner. What you will do is use a bolt leader like part # 80101-1 to fish the bolts into the frame from a different opening then out through the hitch mounting hole. You will probably have to drill out the factory weldnuts if they are still present. I have linked a video below that shows this process in detail. Do not drill new bolt holes in the hitch. This will void your warranty.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 5500 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Search Results: 118137
- Search Results: 7 way to 4 way converter
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Shop: Trailer Wiring
- Shop: BOLT brand vehicle and hitch locks
- Shop: Base Plate for Tow Bar
- Shop: Off Road Lights
- Q&A: Recommended Trailer Hitch for 2007 Toyota 4Runner that Dpes Not Require Fascia Trimming
- Video: Curt Mounting Bracket for 5-Way Flat Trailer Connector Spec Review
- Video: An In-Depth Look at the Curt 7-Way Trailer Plug Extension
- Video: Ultimate Overview of the Curt 7-Way Trailer Plug Extension
- Video: A Closer Look at the Wesbar Adapter
- Video: The Low-Down on the Adapter 7 Pole to 5 Pole Flat Wired Adapter
- Video: Comprehensive Review: etrailer Hitch Pin Alignment Collar for 2" Hitch Accessories
- Q&A: Does Installation of Curt Hitch Require Specific Bumper or Modification on 2007 Toyota 4Runner
- Q&A: What Trailer Connector Mounting Bracket Is Needed For A Trailer Hitch On A 2005 Toyota 4Runner
- Q&A: Hitch Recommendation for a 2006 Toyota 4Runner that Does not Require Fascia Trimming
- Q&A: Recommended 7-way to 4-way Flat Trailer Connector Adapter
- Shop: Adapter 7 Pole to 5 Pole Flat Wired Adapter
- Shop: Curt No-Drill Bracket for 6-Way or 7-Way Round Trailer Connector Mounting Bracket - Long
- Shop: Curt Mounting Bracket for 5-Way Flat Trailer Connector
- Shop: Replacement Mounting Bracket for Hopkins 7- and 4-Pole Trailer Connector Socket
- Shop: Mounting Bracket 4-Pole Flat
- Q&A: Is Loctite Required When Installing a Trailer Hitch
- Q&A: Mounting the Replacement Wiring Harness For Factory 7-Way On a 2008 Toyota 4Runner
- Article: 5 Things to Know About Weight Distribution Hitches
- Article: My Trailer Hitch Doesn't Fit
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
on Trailer Hitch
Christopher
7/30/2024
Thanks. Appreciate the help.