7-Way and Brake Controller Recommendation for 2008 Volvo XC90 with 4-Way

Question

Question:

Hi there, I have a 2008 volvo xc90 already wired with a 4 pin trailer connector. I would like to add a seven pin connector and brake controller. I realize there are multiple brake controllers to choose from. Can you tell me which wiring kit I need for the seven pin connector, wiring to my brakes and then the options for connecting to a brake controller? Ill be pulling a trailer that is approximately 2800 fully loaded. Thank you. John

asked by: John V

0

Expert Reply:

Hey John, so the # ETBC7 that you referenced is the correct kit to convert your 4-way to a 7-way and wire in a brake controller so you are on the right track. So then for a brake controller I really like the Redarc Tow Pro Liberty part # RED52VR which only puts a small knob on the dash of your vehicle and uses an internal sensor to determine how hard to apply the trailer brakes.

expert reply by: Jameson C

0

John V.

7/14/2024

Hi Jameson, Thanks for your response. Is there a less expensive controller option you can recommend? Thanks, John

Jameson C.

7/15/2024

@JohnV Absolutely.. the Tekonsha Brake EVN part # TK63VR is a really great option that works well and is priced great. In this price range there's nothing that comes close.

Jameson C.

7/15/2024

@JohnV Actually the Brake Evn is out of stock till like August so I would go with the P2 part # 90885.

Answer 1

When installing the Universal Installation Kit for Trailer Brake Controller #ETBC7 it isn't necessary to connect the ground wire from the brake controller directly to the negative terminal on your vehicle battery - just find a sufficient mounting…

view full answer...

Answer 2

We have just what you are looking for. If you do not have a 4-way connector on your 4Runner I recommend first installing the Hopkins Plug-In Simple Vehicle Wiring Harness, part #HM43415. This harness plugs into the connection points in the rear cargo…

view full answer...

Answer 3

The Curt Easy Mount Bracket #C58003 would not work for you because it is for a 2-1/2" hitch. Instead, you would want to use Easy Mount Bracket #C58000. Another simple option would be the Curt No-Drill Bracket #C57202. I've added links to…

view full answer...

Answer 4

Running the 10 gauge wire to install the brake controller in your 2011 Toyota Highlander on the interior of the vehicle would be just fine. Most people run the wires on the exterior but having them on interior is perfectly fine as well. The only…

view full answer...

Answer 5

Hi Emily! The hitches with hidden crosstubes, like the Draw-Tite #76194 for your 2017 Volvo XC90, look nicer than a standard hitch style but they do present a challenge when it comes to establishing an anchor point for a wiring kit. Some people will…

view full answer...

Answer 6

The reason the Draw Tite hitch part #76194 can't be used with a weight distribution system is due to how it attaches to the vehicle. What we have found is that if it attaches along the bottom of the frame rails it can be used with a WD system,…

view full answer...

Answer 7

You will need to start with a 4-way (if you do not have one) installed on your 2012 Volvo XC60 to install a brake controller. For that you would want the #118739 which I attached an install video for. From there you would need to convert the 4-way to…

view full answer...

Answer 8

A direct replacement for your Winntec Model 6020 is the Automatic Changeover RV LP Gas Regulator #37207-30395 as the BTU rating is compatible and they have the same fitting sizes.

view full answer...

Answer 9

We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any damage…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

7-Way and Brake Controller Recommendation for 2008 Volvo XC90 with 4-Way

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching