Can I Use the Curt 58963 Tow Harness and the Curt C56406 4-Way Connector on a 2020 Jeep Cherokee?

Question

Question:

Looking at putting a towed vehicle rv wiring harness 58963 and a trailer wiring harness C56406 on a 2020 Jeep Cherokee Trailhawk without factory tow package. Question is will they both fit in area of tail lights and does it matter in what sequence each is plugged into the wiring.

asked by: Bob T

0

Expert Reply:

Yes, they will both work with your 2020 Jeep Cherokee so long as you do not have the tow package. The Curt dinghy tow harness 58963 and the Curt T-Connector Vehicle Wiring Harness item # C56406 connect in line to your factory wiring harness. As far as having enough room there's plenty you'll just have to push the wires down below the lights.

I have linked an installation video below that'll help you get the 4-Way set up.

Please note that you can not use the 4-way when you're flat towing your Jeep. We have had multiple customers encounter this issue.

expert reply by: Jerred H

0

Bob T.

5/3/2024

Thank you very much. This will help.

Jerred H.

5/3/2024

@BobT You're very welcome Bob!

Answer 1

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 2

Thanks for reaching out, Ryan. There are a few differences between the hitches. The B&W hitch part #BW82PR has a slightly higher towing capacity but the ground clearance is less. You will have 11-3/4" ground clearance with the B&W but…

view full answer...

Answer 3

Yes, there is Jason. We actually have two different options and which one you need is going to depend on whether or not your 2025 Kia Telluride has LED lights. I have listed both of them below: With LED Lights - Curt T-Connector Vehicle Wiring…

view full answer...

Answer 4

The factory wiring for both the 2023 and 2024 Hyundai Palisade has been a complicated subject. The pre-wiring you're referring to is not an actual trailer connector. You should have factory wiring and connectors which will allow you to add an OEM…

view full answer...

Answer 5

You can use a 7-Way and 4-Way connector at the same time just as long as you are not overloading the light circuits. If your camper has a lot of outside lights like running lights, and brake/stop/turn lights then the lights that perform the same…

view full answer...

Answer 6

The best method for locating the correct wires to splice into on your 2019 Jeep Cherokee when installing the Tow Ready Taillight Diode System #TR118821 is to simply test them using a circuit tester like #PTW2993. Going by wire color alone isn't…

view full answer...

Answer 7

The vehicle side connector for trailer wiring on a 2010 Lexus RX 350 will be located behind the rear bumper more on the driver side of the vehicle. The connector will connect to the vehicle end of the Tow Ready wiring harness (gray plug) #118252. I…

view full answer...

Answer 8

Hello Lyle, Yes, you can install the Curt T-Connector with the Demco Stay-n-play. The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C56406 will fit your 2019 Jeep Cherokee Trailhawk. The #C56406 is intended to put the 4…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Can I Use the Curt 58963 Tow Harness and the Curt C56406 4-Way Connector on a 2020 Jeep Cherokee?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching