Bearings, Races and Grease Seal For a TDE 46845 Hub On a 5 Starr Boat Trailer
Published 03/12/2024
Products Featured in This Question
Question:
I have a 5 Starr boat trailer Looking for seals and bearings for a TDE 46845 disk brake 5 bolt hub for a tapered spindle Looking for 4 sets Do you carry this?
asked by: Dan G
Expert Reply:
We have found your TDE46845 hub uses a Inner Bearing # L68149, Outer Bearing # L44649 and Grease Seal # 168255TB. While we do not have these in a specific kit you can order 4 of each to work on your trailer. Do be sure to change out the Inner Race # L68111 and Outer Race # L44610 when you change the bearings.
We have the Seal Puller # PTW1219 and Install Kit # PTW83020 which will make removal and installation of the seals and races easier. We also have the Grease # L11390 that I recommend for your hubs with the Bearing Packer # PTW1218 to ensure you get grease fully pressed into the bearings before installing them
Product Page this Question was Asked From
Replacement Trailer Hub Bearing - L68149
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.38 Inch I.D.
- Bearing L68149
- Race L68111
- 3500 lbs Axle
- etrailer
more information >
Continue Researching
- Q&A: Replacement Hub/Rotor Assembly for a Dexter Boat Trailer Axle DX67HR
- Search Results: 46845
- Search Results: race l68111 trailer bearings races seals caps
- Search Results: 171255uc
- Search Results: l68149
- Search Results: tde 46845
- Search Results: l68149 / l68149 trailer hubs and drums
- Search Results: trailer axles
- Shop: Dexter 9-3/4" Hub-and-Rotor Assembly - 5 on 4-1/2 - Zinc - 4,200 lbs
- Video: A Closer Look at the 7-Piece Installation Set for Bearings, Races, and Seals
- Video: A Closer Look at the TruRyde 2.44 Inch OD Drive In with Plug Grease Cap
- Shop: Replacement Grease Cap for Dexter/Tie Down Engineering Vortex Trailer Hubs
- Q&A: Replacement Bearing Kit for TDE 46845 Hub
- Q&A: Bearing Kit for Load Rite Boat Trailer with TDE Hub 46845
- Q&A: Recommended Replacement Hub, Rotor, and Bearings for a Integral Knott Rotor
- Q&A: Replacing Older Tie Down Engineering 46210 and 46845 Trailer Hubs
- Q&A: How to Determine Correct Replacement Hub for Boat Trailer
- Q&A: Replacement Hub/Rotor and Bearings for Tie Down Engineering TDE46245
- Shop: Trailer Idler Hub Assembly for 4,200-lb Axles - 5 on 4-1/2 - Galvanized
- Video: Review of Dexter Trailer Hubs and Drums - Hub with Integrated Rotor - DX82UR
- Shop: 2.44" OD EZ Lube Grease Cap - Drive In - Qty 1
- Shop: Dexter Boat Trailer Axle - 89" Long - Galvanized
- Shop: Replacement EZ Lube Drive-In Grease Cap - 1.986" OD - Qty 1
- Shop: DeeMaxx Stainless Steel Drive-In Grease Cap w/ Plug - 2.45" Outer Diameter
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: Measuring To Choose The Right Trailer Axle
on Trailer Bearings Races Seals Caps
