Will The Torklift StableLoad # TLA7311 Work With An Air Bag Kit?

Question

Question:

Will the StableLoad - A7311 work with air bags. If not is there any other equivalent options?

asked by: Lance M

0

Expert Reply:

Yes, the Torklift StableLoad # TLA7311 will indeed work with an air bag kit. This is actually a combination we recommend fairly frequently as the two work very well together. The StableLoads will preload the overload spring which will add support to your suspension and prevent bottoming out. Air bags will also help to prevent this, but adding the StableLoads means the air bags will not need to be filled nearly as full in order to get the truck level, so you get good support without making the ride too rough. Basically, the suspension will function more as it was designed from the factory - only better.

expert reply by: Jesse M

0

Answer 1

There are a couple things to consider between using the Torklift StableLoad #TLA7200 and air bags on your 2022 Ford F-350 Super Duty when transporting your in-bed camper. If you are just looking to decrease sway, the Torklift StableLoad #TLA7200 is a…

view full answer...

Answer 2

Looks like your generator uses a standard 240 volt 30 amp style connector which would use both pin on the female side of the #A10-G30430VP you referenced. For connecting your generator to a 30 amp socket on an RV this adapter would work well. It will…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 10

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 11

Hey Mark, welcome to the fifth wheel community! I'd be more than happy to help you. So a fifth wheel hitch will sit lower than the top of the truck bed rails so you wouldn't have to remove the head of the hitch to close the cover BUT the…

view full answer...

Answer 12

Hey Mark, the only real downside to an offset ball like the Gen-Y part #GY43XR is going to be that it costs more typically and it would take up more room when stored compared to a non-offset ball like the #C38CR. The handling and weight carrying…

view full answer...

Will The Torklift StableLoad # TLA7311 Work With An Air Bag Kit?

Product Page this Question was Asked From

Continue Researching