Can Ladder Roller for Rhino-Rack Heavy-Duty Crossbars RR1500 Work on Square Bars

Question

Question:

Will this roller work with square bars?

asked by: Mark H

0

Expert Reply:

If the square bars were the Rhino Rack HD crossbars that have channels that along the top of them yes the Ladder Roller for Rhino-Rack Heavy-Duty Crossbars # RR1500 would work. If they are standard square bars like from Thule it would not work.

expert reply by: Jameson C

0

Answer 1

Hey Brian, thanks for reaching out. I went out to our warehouse and measured one of the etrailer Sidewind Aluminum Jacks #e95YV. The distance from the center of the bracket to the bottom of the wheel is approximately 14" with the jack fully…

view full answer...

Answer 2

Hey Brian! Yep, for your boat trailer, I’d skip the etrailer A-frame drill jack #e38AV since your trailer doesn't have that standard 3-bolt A-frame jack mount. That could be fabricated to fit, but that's a lot of unnecessary work. For a…

view full answer...

Answer 3

Good morning Frank! The etrailer Sidewind Aluminum Jack with Wheel - Swivel Bolt - 1.5K #e95YV is a really nice option when you want easier operation without wiring an electric jack. It has a 1,500 lb capacity, 12 inches of travel, and a wheel for…

view full answer...

Answer 4

I spoke to my contact at Rhino Rack and he informed me that the length of the roller on the Rhino Rack Ladder Roller #RR1500 that you referenced is 56-1/4 inches. Check out the picture I attached to see this measurement.

view full answer...

Answer 5

We have other options for carrying a kayak, but the Hullavator #TH711420 will not work with your truck due to the lack of overhang of your bars over your feet with the Adarac Ladder Rack #A4001665. If you're looking to load up your kayaks easily,…

view full answer...

Answer 6

We have what you need, but the Ladder Roller for Rhino-Rack Heavy-Duty Crossbars #RR1500 will not fit your Yakima HD bars; it is only a fit for Rhino-Rack HD crossbars. Instead, the correct roller for your Yakima HD bars is the Ladder Roller for…

view full answer...

Answer 7

Good morning Steve! For a boat trailer jack where you still want a wheel, I’d use the etrailer Sidewind Aluminum Jack with Wheel - Swivel Bolt - 1.5K #e95YV. That one gives you a 1,500 lb capacity, 12" of travel, and a built-in wheel so you can…

view full answer...

Answer 8

Hey Wayne! For that kind of garage setup, I’d look at the etrailer Sidewind Aluminum Jack with Wheel - Swivel Bolt - 1.5K #e95YV. It gives you the wheel you need for nudging the tongue around by hand, but it also includes a 19mm socket so you can…

view full answer...

Answer 9

Good morning Eddie! The etrailer Sidewind Aluminum Jack with Wheel - Swivel Bolt - 1.5K #e95YV is the one I’d look at for that. It gives you a 1,500 lb capacity, 12" of travel, and a built-in wheel, so it still works like a normal boat trailer…

view full answer...

Answer 10

Hey Caleb! For a personal watercraft trailer, the etrailer Sidewind Aluminum Jack with Wheel - Swivel Bolt - 1.5K #e95YV is the one I’d use. It is aluminum with stainless steel hardware, so it makes sense for a trailer that sees a lot of ramp use.…

view full answer...

Answer 11

Good morning Ron! Yes, for a boat trailer where you still want a wheel, the etrailer Sidewind Aluminum Jack with Wheel - Swivel Bolt - 1.5K #e95YV is an excellent option. It has a 1,500 lb capacity, 12" of travel, a built-in wheel for…

view full answer...

Answer 12

Good morning Terry! Yes, for a boat trailer, the etrailer Sidewind Aluminum Jack with Wheel - Swivel Bolt - 1.5K #e95YV is the one I’d start with. It is the silver aluminum version with the wheel, and it was built more with boat trailer use in mind…

view full answer...

Can Ladder Roller for Rhino-Rack Heavy-Duty Crossbars RR1500 Work on Square Bars

Product Page this Question was Asked From

Continue Researching