Ladder Roller for Yakima HD Crossbars

Question

Question:

rhino rack roller rr1500 Will this roller fit my Yakima HD bar

asked by: Jim R

1

Helpful Expert Reply:

We have what you need, but the Ladder Roller for Rhino-Rack Heavy-Duty Crossbars # RR1500 will not fit your Yakima HD bars; it is only a fit for Rhino-Rack HD crossbars.

Instead, the correct roller for your Yakima HD bars is the Ladder Roller for Yakima HD Bar, JetStream, FlushBar, and RailBar Crossbars # Y01163.

I have added a link to a video review of this roller for you to check out as well.

expert reply by: Kyle S

1

Answer 1

If the square bars were the Rhino Rack HD crossbars that have channels that along the top of them yes the Ladder Roller for Rhino-Rack Heavy-Duty Crossbars #RR1500 would work. If they are standard square bars like from Thule it would not work.

view full answer...

Answer 2

I spoke to my contact at Rhino Rack and he informed me that the length of the roller on the Rhino Rack Ladder Roller #RR1500 that you referenced is 56-1/4 inches. Check out the picture I attached to see this measurement.

view full answer...

Answer 3

We have other options for carrying a kayak, but the Hullavator #TH711420 will not work with your truck due to the lack of overhang of your bars over your feet with the Adarac Ladder Rack #A4001665. If you're looking to load up your kayaks easily,…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Steve; the factory hitch on the 2013 Tacoma has the bumper brackets integrated into the hitch. You can replace it with the etrailer Trailer Hitch #e98850 but you will have to remove the old hitch and find new bumper brackets to complete the…

view full answer...

Answer 7

Sure, I can help with that. I can see why the fitment notes are confusing. For a 2012 Toyota Tundra with the factory tow package and factory 7 way connector, you'll want a brake controller that plugs into the factory brake controller port under…

view full answer...

Answer 8

There are a couple of differences between the two. The JetStream bars like #Y00425 are made of extruded aluminum while the CoreBars such as the #Y00421 you've looked at are constructed of galvanized steel. As you've mentioned, the CoreBar has…

view full answer...

Answer 9

Hey, Andrew! If you have the inside bed rails, you won't have to do any sort of modifications to be able to install the Extang Trifecta Signature 2.0 tonneau cover part #EX94915. The Instructions will go over how to install the cover if you do or…

view full answer...

Answer 10

Hey Jason, whenever available I would recommend going with the channel attachment for roof rack accessories including the Thule Hullavator part #TH898 as its simpler stronger, and it's basically the future of most roof rack accessories as it…

view full answer...

Answer 11

If your trailer's roof is only 1-1/2" thick, you can still use the Furrion Chill #FR52PR but you will need to build up a lip of sorts on the roof where you'll be installing this to make up for the difference. There isn't a specific…

view full answer...

Answer 12

The correct Pop and Lock tailgate lock for your 2013 Toyota Tacoma with a backup camera is the part #PAL5400 which comes with a lock cylinder that will allow you to key to your truck's key. I attached an install video for this for you to check…

view full answer...

Ladder Roller for Yakima HD Crossbars

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching