Replacement Hardware For a Curt Trailer Hitch Receiver # C13146

Question

Question:

Hi do you carry the bolts for Curt Trailer Hitch C13146 if so how con i look for it in your website.

asked by: Zipalees L

0

Expert Reply:

To get all the hardware for the Curt Trailer Hitch Receiver # C13146 you can order the Replacement Hardware Kit # RHK. Be sure to enter the hitch number in the box when ordering. Otherwise you can source the six M14-1.50 x 40mm, CL 10.9 hex bolts or six 9/16" conical-toothed washers at a local hardware store.

expert reply by: Bud M

0

Jarrett

1/4/2026

Looking to for the hex bolts for a curt class 3 hitch for my 2025 Hyundai Santa Cruz xrt

Jerred H.

1/4/2026

@Jarrett The Replacement Hardware Kit item # RHK is our only option to provide any of the hardware needed to install your Curt item # C23WR hitch.

Bob

8/10/2026

Besides the flange nuts and washers, what does the "kit"come with?

Christopher H.

8/10/2026

@Bob The hardware that comes with # RHK is going to dependent upon what hitch part number you enter when ordering. Is there a specific hitch you are attempting to source replacement hardware for?

Bob

8/10/2026

@ChristopherH Yes, it would be for this entry Curt #13146

Christopher H.

8/10/2026

@Bob For the # C13146, the # RHK would include six M14-1.50 x 40mm, CL 10.9 hex bolts and six 9/16" conical-toothed washers. This is all of the hardware required for the installation of this specific hitch. As mentioned above, sourcing this hardware locally may be more cost effective.

Answer 1

There are differences in them but we do have what you are looking for and they can in some situations be used together. The Replacement Trailer Hub Bearing you have part #02475 and Replacement Race for 02475 Bearing part #02420 are designed to work…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 9

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 10

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Replacement Hardware For a Curt Trailer Hitch Receiver # C13146

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching