What Size Drill Bit is Needed for Lippert Scissor Stabilizer Jacks

Question

Question:

What size drill bit to drill into my camper to install these jacks

asked by: Jack P

1

Helpful Expert Reply:

The Lippert Scissor Stabilizer Jacks part # LC285326 will require a 5/16" drill bit for installation. The holes once drilled will be used to secure the jacks with the included self-threading bolts.

expert reply by: Conner L

1

Answer 1

The electric brake control harness on your 2011 Toyota Tacoma will be located underneath the drivers side dash to the left of the steering column. It should be taped to another harness near the emergency brake pedal. It will be a 5-pin connector. I…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Sure, I can help with that. I can see why the fitment notes are confusing. For a 2012 Toyota Tundra with the factory tow package and factory 7 way connector, you'll want a brake controller that plugs into the factory brake controller port under…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 10

Hey Dale, thanks for reaching out. For your 2010 Toyota Tundra with the factory tow package, a proportional controller is definitely the way to go for smooth braking on a 2-axle trailer, and a really clean option is the Redarc Tow-Pro Liberty…

view full answer...

Answer 11

Hi Steve; the factory hitch on the 2013 Tacoma has the bumper brackets integrated into the hitch. You can replace it with the etrailer Trailer Hitch #e98850 but you will have to remove the old hitch and find new bumper brackets to complete the…

view full answer...

Answer 12

The Redarc Tow-Pro Liberty #RED24FR is the way to go over the Elite #RED44FR as you get the nicer functions of the Elite at a lower price. The Elite has the ability to be the more preferred proportional style of controller as well as a time-delayed…

view full answer...

What Size Drill Bit is Needed for Lippert Scissor Stabilizer Jacks

Product Page this Question was Asked From

Continue Researching