Brake Controller Installation Port Location on a 2011 Toyota Tacoma

Question

Question:

has all towing fuses but cannot find the conector

asked by: Bill N

0

Expert Reply:

The electric brake control harness on your 2011 Toyota Tacoma will be located underneath the drivers side dash to the left of the steering column. It should be taped to another harness near the emergency brake pedal. It will be a 5-pin connector.

I have attached a photo showing the location of this harness as well as the installation instructions for the Plug-In Adapter from Tekonsha, # 3040-P, for you to check out.

expert reply by: Jameson C

0

click to enlarge

Answer 1

It sounds like you're looking for a weight distribution hitch for your camper, which we do recommend any time the trailer that you'll be towing weighs more than 50% of the weight of your vehicle. When it comes to choosing a weight…

view full answer...

Answer 2

Tongue weight is typically between 10% and 15% of your trailer's total weight. That would put your 3,500 lbs trailer's tongue weight around 350 lbs to 525 lbs. With this in mind, I recommend the Equal-i-zer Weight Distribution System w/…

view full answer...

Answer 3

Unfortunately, we do not have the 14” diameter x 2” wide braking assemblies you need for your trailer. I also did some searching online and could not find any replacement parts for you either. The only option I can offer you would be to replace with…

view full answer...

Answer 4

The Lippert Scissor Stabilizer Jacks part #LC285326 will require a 5/16" drill bit for installation. The holes once drilled will be used to secure the jacks with the included self-threading bolts.

view full answer...

Answer 5

Which Prodigy do you have, the original or the P2? My contact at Tekonsha tells me that if the power to controller is interrupted and re-established in rapid succession, like when you are replacing your battery, the processor of the original Prodigy…

view full answer...

Answer 6

Brake controllers like the Prodigy P2 #90885 will have a slight draw on the vehicle battery when the vehicle is off. The two dots you are referring to will stay on for up to 15 minutes and then the controller will go into sleep mode and the dots will…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Brake Controller Installation Port Location on a 2011 Toyota Tacoma

Continue Researching