Grease Seal For a 1" Straight Spindle and Bearing Buddy Bearing Protectors

Question

Question:

I have a 1 straight spindle and looking for bearing seals with a 1.23 ID. I do have bearing buddies and it would be great for a seal for that system. Im looking for part numbers. Thank you

asked by: Scott

0

Expert Reply:

The Spindle Grease Seal Set # BB60001 is specifically designed to fit on your 1" straight spindle using a Bearing # L44643 and 1.980 Bearing Buddy like Set # BB1980A-SS. The seal set includes 2 smooth stainless steel rings, 2 O-rings and 2 grease seals for both hubs of your axle.

expert reply by: Bud M

0

Answer 1

Okay, we definitely have a solution for you here, and I'll start with the clearance; with trailer tires you need to have 3" of clearance from the top of the tire to your fender and at least 1" of clearance between the inside of the tire…

view full answer...

Answer 2

Shoreland'r parts are not something that we carry but their numbers are often associated with common parts. The 4410275 is the same as the GS-1250XDL which doesn't come back to anything we have information on. There is a GS-1250DL which…

view full answer...

Answer 3

The bearing part #L44649 has an inner diameter of 1.063 and is typically used in 3,500 lb axle hubs and the #L44643 has an inner diameter of 1 inch and is typically used on 2,000 lb axle hubs. If you can get me more info on your trailer like axle…

view full answer...

Answer 4

The closest option we have would be the part #BB60001 which has an inner diameter of 1.375 inches and an outer diameter of 1.980 inches.

view full answer...

Answer 5

Grease seal set #BB60005 has an inner diameter of 1.375 (1 3/8) and an outer diameter of 1.980. These should work for both of your trailers.

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Grease Seal For a 1" Straight Spindle and Bearing Buddy Bearing Protectors

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching