Replacement Inner Member Of Dexter DX7.5L A-60 Brake Actuator

Question

Question:

Looking to replace my actuator on a 2-disc boat trailer with Item # DX56FR and with my set up I am looking to remove the outer shell of the actuator and just bolt on the inner shell. Is there any reason why I cannot or would not want to do that?

asked by: Dave

0

Expert Reply:

We do carry the Replacement Inner Member # DX99FR that fit the Dexter DX7.5L A-60 Brake Actuator # DX56FR and Legacy UFP brake actuators. This would allow you to replace just the inner portion of your current actuator as long as yours is one of the above actuators.

expert reply by: Bud M

0

Answer 1

If you have a coupler actuator that looks like the #DX29FR but it mounts inside the channel on the trailer frame what you would most likely actually want is the inner member of this coupler with the part #DX99FR. This is the inner section of the…

view full answer...

Answer 2

The main difference between The Dexter Inner Membrane #DX99FR and The Dexter inner Membrane #DX39FR is that the #DX99FR is for a tandem axle with disc brake setup. The #DX39FR is for a single axle with disc brake setup. Both Dexter membranes have a 2…

view full answer...

Answer 3

Yes, the replacement inner member part #DX99FR does fit your UFP A-60 actuator and will work perfectly fine with the tandem axle disc brake setup you have now.

view full answer...

Answer 4

We do have the Replacement Inner Member for Dexter DX7.5L Actuators and Disc brakes. You would need to select the Single Axle #DX39FR or Tandem Axle #DX99FR version.

view full answer...

Answer 5

We do have a potential solution for you. Unfortunately, the swing away actuators like the one on your 2005 Mastercraft trailer have been discontinued, so I am afraid there is no direct replacement, or anything that will fit inside the current swing…

view full answer...

Answer 6

The pins on the Dexter DX7.5L A-60 Brake Actuator #DX63FR are removed by releasing the snap rings and washers from one side of the actuator. You will then be able to press out the pins. Do note depending on the age of your actuator and the amount of…

view full answer...

Answer 7

Yes, you could remove the inner member of the Dexter DX7.5L A-60 to replace the bad member of your UFP A-60. Our pricing algorithm can be a little confusing so if this is the less expensive route than just the inner member part #DX99FR it is what I…

view full answer...

Answer 8

We have the inner member for the Dexter Brake Actuator part #DX56FR with the #DX99FR which is what you are looking for. This is a 7,500 lb rated disc brake inner member that is compatible with tandem axle setups.

view full answer...

Answer 9

The Replacement Shock Absorber Spring Kit #TK71-758-00 is the correct shock for your UFP Surge Brake Actuator. The picture you included does not specify if it is for a disc or drum brake set, so I have found both for you to choose from. Disc Brake…

view full answer...

Answer 10

For a replacement shock you're going to want the Replacement Shock Absorber Spring Kit for Dexter Brake Actuators #TK71-758-00, and for the replacement master cylinder you'll just need the Replacement Master Cylinder Assembly for Dexter Brake…

view full answer...

Answer 11

Thank you for all of the info! I did some digging and found out that your older Fulton A60 swing away actuator was actually a UFP A60 actuator on a Fulton coupler hinge like part #FHDPW330300. I was able to speak with my contact at Dexter who said…

view full answer...

Answer 12

For a replacement I recommend the Dexter DX7.5L A-60 Brake Actuator #DX27FR. The swing-away actuators like your old A60 have been discontinued, along with replacement parts, so this is the best solution. This features a 7,500 lb trailer capacity,…

view full answer...

Replacement Inner Member Of Dexter DX7.5L A-60 Brake Actuator

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching