How Are The Pins Removed On The Dexter DX7.5L A-60 Brake Actuator # DX63FR For Replacing Parts?
Updated 09/25/2023 | Published 09/23/2023
Products Featured in This Question
Question:
How do you remove the front pin to replace parts
asked by: Bruce
Expert Reply:
The pins on the Dexter DX7.5L A-60 Brake Actuator # DX63FR are removed by releasing the snap rings and washers from one side of the actuator. You will then be able to press out the pins. Do note depending on the age of your actuator and the amount of corrosion you may need some penetrating oil to help break the pins free from the sleeves inside the actuator. If the pin will still not release you can lightly tap on the end of the pin but be sure to be careful to not damage the retaining portion for the snap rings if you plan on reusing your pins.
We do have the Replacement Inner Member # DX99FR which will give you all new inner components and pins.
Product Page this Question was Asked From
Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Weld On - Disc - 2" Ball - 7.5K
- Brake Actuator
- Surge Brake Actuator
- Farm Trailer
- Boat Trailer
- Construction Trailer
- Travel Trailer
- Utility Trailer
- Weld-On
- 7500 lbs GTW
- 2 Inch Ball Coupler
- 3 Inch Channel Tongue
- Disc Brakes
- Electric Lockout
- Dexter
more information >
Continue Researching
- Shop: Dexter DX7.5L A-60 Brake Actuator - Weld On - Drum - 2" Ball - Primed - 7,500 lbs
- Shop: Replacement Inner Member for Dexter DX7.5L Actuator - Tandem Axle w/ Disc - 2" Ball - 7,500 lbs
- Shop: BOLT brand vehicle and hitch locks
- Search Results: sleeve
- Search Results: dexter 010 060 00
- Search Results: license plates and frames
- Search Results: spindle wear sleeve
- Search Results: license plates
- Search Results: wear sleeve
- Search Results: brake hose
- Shop: DeeMaxx Hydraulic Brake Line - Rubber - 3/16" Brass Male Inverted Flares - 20' Long
- Q&A: Can Bearing Buddy Grease Seal Sets Be Used With BTR EZ Lube Spindles?
- Q&A: Compatibility of Dexter DX99FR Inner Member for Disc Brake Actuator with Ranger Boat Trailer
- Q&A: How to bleed the brakes on a surge brake actuator on boat trailer
- Q&A: Replacement Actuator for UFP A-60 34044
- Shop: Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K
- Shop: TorkLift's Universal License Plate Flip Down Kit - Bolt-On Bracket for Hitch Access
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Shop: Dexter Zinc-Plated, A-60 Coupler - 2" Ball - 3" Channel - Bolt On - 5,000 lbs
- Shop: Spindle Grease Seal Set for LM48548 or L68149 Inner Bearing and 1.980, 1.968 or 2.562 Bearing Buddy
- Video: Replacement Inner Member for Dexter DX7.5L Actuator Spec Review
- Q&A: Replacement Inner Member for UFP A-60 Tandem Disc Brake Actuator
- Q&A: Correct Replacement for UFP A-60 or A-75 Brake Actuator
- Q&A: Recommended Conversion Kit for Disc Brakes On 7,000 Lb Dexter Axles
- Video: Breaking Down the Fulton Fold-Away Coupler Hinge Kit for 2" x 3" Trailer Tongue
- Video: Dexter 10" Hub-and-Rotor Assembly: The Breakdown