Optional Lengths For Lock N Roll Articulating Trailer Coupler for 2" Receivers

Question

Question:

Do you offer a longer Lock N Roll Articulating Trailer Coupler for 2" Receivers - Trailer Side - 11,000 lbs Item # 336TS510?

asked by: Bobby A

0

Expert Reply:

Yes, we carry the Lock N Roll Articulating Trailer Coupler for 2" Receivers in 3 different lengths. The # 336TS510 you found is 9-3/4" from the hitch pin center hole to the center of the coupler head. We also have it in a 18-1/2" Length # 336TS520 and a 33-1/2" Length # 336TS526.

expert reply by: Bud M

0

Answer 1

Hey Donnie! An articulating coupler like the #336TS510 is definitely safe to use. I don't know about other brands, but the Lock N Roll is incredibly secure so that isn't a concern. If you're off-roading with the trailer then an…

view full answer...

Answer 2

The 360 degree rotation of the Lock N Roll Articulating Trailer Coupler #336VS511, along with the left to right and up and down articulation allows fantastic maneuverability, especially when backing a trailer around a corner and into a tight spot.…

view full answer...

Answer 3

What you have in your picture is a 6mm x 1 low profile zerk fitting. It was recently added to the design and it is used to insert grease into the hinge.

view full answer...

Answer 4

To utilize the Lock N Roll coupler system on your trailer you'll need one of the following styles: - A-Frame #336TS504 - Flat Plate #336TS514 - 2" Channel #336TS528 - 2-1/2" Channel #336TS506 - 3" Channel #336TS508 The part…

view full answer...

Answer 5

The distance from the center of the hitch pin hole of the Lock N Roll Articulating Trailer Coupler for 2" Receivers #336TS510 to the center of the coupling pin measures 9-3/4 inches.

view full answer...

Answer 6

I spoke with my contact at Lock N Roll about the Lock N Roll Articulating Hitch part #336VS503505 and they were not quite sure what measurements you are looking for nor was I. That said, I went out to our warehouse for you and jotted down a few…

view full answer...

Answer 7

Your 2017 JK Wrangler won't have the connector at the rear for the #42145 unless it was equipped with the factory tow package. No worries, though. We can make this happen with a minimum of hassle, though it's not quite plug-and-play.…

view full answer...

Answer 8

Yes, you can use the Curt Weight Distribution Shank #C17124 will work with your EAZ-Lift R3 Weight Distribution Hitch. Weight distribution shanks from different brands are all made with a standard hole diameter and spacing. This shank is made for…

view full answer...

Answer 9

I went out to the warehouse and pulled trailer hub #84545BX. The outer diameter of the center bore is 2.59 inches. I used a set of digital calipers to take the measurement.

view full answer...

Answer 10

The etrailer A-Frame Trailer Coupler w/ Round Jack Hole #CA-5280-RB uses the standard a-frame angle of 50 degrees. The length from the rear of the coupler to where the coupler meets its narrowest point is approximately 9" long. I have include…

view full answer...

Answer 11

In order to choose the correct Lock N Roll Articulating Trailer Hitch you'll need to measure from the ground to the center of the trailer hitch on the vehicle and then from the ground to the top of the frame on the trailer and subtract 1" -…

view full answer...

Answer 12

Hey Steven, I recommend going with the Lock N Roll Articulating Trailer Hitch for 2" Receivers #336VS501 because it is a fully-articulating connection that uses pins instead of a round hitch ball connection so you can be completely confident…

view full answer...