Bike Adapter Bar w/ a 50 lbs Capacity

Question

Question:

Hi, I need an adaptor bar that fits 20inch from seat post to handle bar stem and can hold a bike weighing 42 lbs. Can you please suggest one. Thank you

asked by: Brittany

0

Expert Reply:

For a bike that weighs 42 lbs you will need the Thule Bike Adapter Bar for Women's and Alternative Frame Bikes item # TH982XT. This adapter bar has a 50 lbs capacity and can telescope from 16" - 31-1/2".

expert reply by: Jerred H

0

Answer 1

I can help you pick out a bike rack that will be compatible with your Curt 1-1/4 Class I hitch #C11065 on your 2011 Volvo C70. The first thing we know is that from the center of your hitch pin hole to the edge of your bumper will need a rack with at…

view full answer...

Answer 2

According to SportRack, the capacity of their Frame Adapter Bar #SR0500 is 35 lbs. I've checked with our other bike rack manufacturers such as Thule, Yakima, Kuat and Swagman among others, and have found that the 35 lb capacity is typical. Over…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Bike Adapter Bar w/ a 50 lbs Capacity

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching