Universal Hitch for a Freightliner P700 or M45

Question

Question:

Can I tow with freightliner p700 or m45 I’m looking to tow a two behind compressor approx 2500 lbs if impossible what parts tow hitch will I need thanks for your import

asked by: Joseph

0

Expert Reply:

The only styles of hitches that can be made to fit a service body truck like your Freightliner P700 or M45 are universal hitches like the Class V Universal Weld-on Receiver Hitch and Brackets with 3" Drop item # 15901.

expert reply by: Jerred H

0

Draw-Tite Weld on Brackets 7 & 16 inches
(click to enlarge)

Answer 1

Hi Brad, Yes, the Draw-Tite #65033 sits much lower to clear the air dam, while the Curt Front Mount Trailer Hitch Receiver #31320 sits higher, requiring you to trim the air dam. These both have a 5,000lb capacity so you should definitely make sure…

view full answer...

Answer 2

Please refer to the included images I made showing measurements for Curt trailer hitch #C14048. This hitch is designed to fit 1999 to 2016 Ford cab and chassis model trucks. Those are the trucks sold without a bed and are then turned into service…

view full answer...

Answer 3

The Curt Trailer Hitch Receiver #C15410 is 37" wide and the bolt hole slots are 34-1/4" on center from drivers side frame rail to passenger side frame rail.

view full answer...

Answer 4

The Curt #C14048 measures 16-1/16 inches from the back to the center of the 3 front holes. Those front holes are all 1-1/2 inches on center so you technically could use the 14.565 inch measurement. There is not one that is closer to 15 inches in…

view full answer...

Answer 5

I checked with Curt and they sent me the following dimensions based on your picture for the #C15410. Red line measurement 10.55” Yellow Line measurement 5.32” Green Line measurement is 7.5”

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

Though the Curt # C13409 and Draw-Tite #76271 are nearly identical to each other, there are a few subtle differences. First being where they sit once installed. The will both have the exact same height of 14-1/2 inches, but the Draw-Tite #76271 will…

view full answer...

Answer 12

Hi John! We definitely have hitches available for your 2026 Lexus RX350h and the etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" #e29ZV is a great option. The matte finish makes our hitches blend in better than…

view full answer...

Universal Hitch for a Freightliner P700 or M45

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching