Recommended Ball Mount for 2013 Honda Pilot
Updated 06/28/2013 | Published 06/26/2013 >
Products Featured in This Question
Question:
My new 2013 Pilot hitch receiver hole for a ball mount is 4inch higher 20.25 at its center than that of my 2003 Pilot hitch hole. My old ball mount had only a 2inch and 6.5inch center to center distance. What and CTC distance would you recommend on a ball mount for my new Pilot? I would be towing a double axle rental trailer, or a jet ski and ATV trailer generally. Should I go as low as a 6inch this time and a longer 8-9inch long shaft?
asked by: Michael M
Expert Reply:
On average, the coupler height of a trailer that is jacked up so that it is level is between 17-19 inches high.
To determine the rise or drop your ballmount needs, jack the trailer so that the frame is level to the ground. Measure from the underside of the coupler down to the ground. Then measure from the top inside edge of the receiver opening to the ground. The difference between these two measurements is the rise or drop needed. If the receiver height of the Pilot is greater than the coupler height of the level trailer, you will need a ball mount with a drop. If the level trailer coupler height is greater than the receiver height of the Pilot, use a ball mount with a rise.
You might find that a ball mount with the exact correct rise or drop is not available. If this is the case, get as close as you can. As long as you are within 2 or so inches of level, you will be fine. Its is preferable to have the trailer ball a bit high than too low.
Since it sounds like you might be towing several different trailers, perhaps an adjustable ball mount like part # TK5007 would be the way to go.
I have linked to our FAQ article that will show you exactly what to measure to determine the rise or drop needed.
The distance between the hitch pin hole and the hole for the trailer ball is typically between 8 and 10 inches, if you choose a ball mount with the proper rise or drop with 8 to 10 inch hole spacing, you should be just fine.
Product Page this Question was Asked From
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- Steel Shank
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Shock Absorbing
- Convert-A-Ball
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Adjustable Ball Mount for 2" Hitches - 9" Rise to 10-1/4" Drop - 5,000 lbs
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Curt Easy Mount Bracket for 4- or 5-Way Flat Trailer Connector - 2" Hitch
- Shop: Curt LED 4-Way Flat Connector (Vehicle End) Tester
- Shop: Curt Mounting Bracket for 4-Pole Flat Trailer Connector
- Shop: No-Drill Mounting Clips for EZ Connector Vehicle-End Trailer Connector - Ford/Toyota
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer wiring
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Brake Controller
- Video: Clean Up Your Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer tires and wheels
- Search Results: trailer hitch ball mount
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Base Plate for Tow Bar
- Search Results: trailer jack
- Q&A: How to Replace a Lance 6-Pin Plug w/ a Standard 7-Way Connector



