Availability of Shank Equivalent to BXW4018 for Blue Ox SwayPro Weight Distribution System

Question

Question:

Looking for shank equivalent to BXW4018 for Swaypro 1500. Do not want BXW4028. Perhaps Equalizer EQ90-02-4700?

asked by: Ron H

0

Expert Reply:

The Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 7" Rise, 3" Drop # EQ90-02-4700 is compatible with your Blue Ox SwayPro # BXW1500. With a 7" rise and 3" drop it will be the closest equivalent to the old BXW4018's 8" rise and 2-1/2" drop.

expert reply by: Robin H

0

Answer 1

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 2

Yes, the Blue Ox SwayPro Weight Distribution Shank part #BXW4028 will work with the Blue Ox SwayPro Weight Distribution part #BXW1503. Please note the above is for underslung (coupler under frame) couplers which are not very common. If you have an…

view full answer...

Answer 3

Sorry to hear about your troubles. Based off of the information you have provided me it sounds like your father in law had a Blue Ox SwayPro System. You're in luck because there are plenty of replacement parts available for this system. To start…

view full answer...

Answer 4

In regards to the Blue Ox SwayPro Weight Distribution Shank part #BXW4028, the distance from the center of the hitch pin hole to the center of the adjustment holes is 9". The overall height of the shank is 12-1/2" when measuring from the…

view full answer...

Answer 5

Since you already have the Blue Ox SwayPro Weight Distribution w/ Sway Control item #BXW1000 I would not recommend buying a new one to go with your Grand Design Imagine 2970rl. The tongue weight range on that Blue Ox is 750-1,000 lbs so you're…

view full answer...

Answer 6

The Weight Distribution Shank for Gen-Y Hitch Adjustable Ball Mounts #325-GH-0352 that you referenced is designed to fit the standard weight distribution heads found on nearly all weight distribution systems. Most of the time if there's an issue…

view full answer...

Answer 7

Yes, you can use the Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers item #325-GH-625 to flat tow with. This adjustable ball mount has a 21,000 lbs capacity and fits a 2-1/2" hitch. It is compatible with the Blue Ox Base Plate Kit item…

view full answer...

Answer 8

Hello Loni. No, the Weight Distribution Shank for Gen-Y Hitch Adjustable Ball Mounts w/ 2-1/2" Receivers - 21K #GY98ER is not compatible because it has a 3/4" pin hole diameter, and the Fastway e2 requires a standard 5/8" pin hole…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Availability of Shank Equivalent to BXW4018 for Blue Ox SwayPro Weight Distribution System

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching