Curt Trailer Hitch C11424 on 2018 Hyundai Elantra Without Factory Tow Loop

Question

Question:

I dont have a tow loop on my car. The hitch is at a downward sloping angle when loaded and wriggles a bit. Do you have any suggestions?

asked by: PATRICK S

0

Expert Reply:

The # C11424 Curt Trailer Hitch Receiver requires the factory tow loop as shown in the instructions for hitch installation. Most are equipped with the tow loop but unfortunately your 2018 Hyundai Elantra was not one of them. Without the tow loop, the hitch won't be securely attached to the vehicle making it unsafe.

To carry bikes on your 2018 Elantra Sedan, you could use a trunk bike rack like the Yakima FullBack # Y02634.

I have attached an installation video for your reference.

expert reply by: Robin H

0

Answer 1

Yes, the 2018 Hyundai Elantra GT does indeed require different hitches than the sedan version. We do have them separated out in our fit guide to avoid confusion. The hitch I recommend is #C11509. This hitch is a confirmed fit for your GT as long as…

view full answer...

Answer 2

Your 2018 Hyundai Elantra does only have one Class I hitch available as long as your Sedan is not the sport model. In that case, we have the Curt #C11424 which is the class I with a 1-1/4 inch receiver. This Curt hitch #C11424 will require the…

view full answer...

Answer 3

We have not yet had a chance to install the Curt Trailer Hitch Receiver #C11424 so unfortunately, we don't currently have a video available. I have however attached the complete install instructions below that you can check out which should give…

view full answer...

Answer 4

The only trailer hitch that fits your 2018 Hyundai Elantra SEL is the part #C11424, and you need to make sure have the factory tow loop (see linked instructions) for this one to fit. If you don't have that factory tow loop then you could use a…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 9

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 10

If your 2020 Hyundai Elantra is a GT Hatchback, the DrawTite Hitch #24905 will fit as long as it is not one of the models that was mad IN Korea. If your 2020 Hyundai Elantra is a GT Hatchback, but is not an N line model and does not have dual…

view full answer...

Curt Trailer Hitch C11424 on 2018 Hyundai Elantra Without Factory Tow Loop

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching