Is There Trimming Required to Install Draw Tite Hitch DT79MR

Question

Question:

Have read several reviews. Does seem to be a question if trimming is required on this hitch. Will be installing on 2021 Honda CRV. Thank-you

asked by: David L

0

Expert Reply:

When installing the Draw Tite hitch part # DT79MR there is trimming required of the rear fascia to allow the hitch opening to pass through.

If you watch the install video I attached you can see the trimming outlined.

expert reply by: Jameson C

0

Answer 1

Hey Sean, if the Draw Tite hitch you have is the #76128 it's not supposed to fit the hybrid models so that would be why you are having the problem you mentioned. The Draw Tite part #DT79MR is instead the one that fits the hybrid models.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The available trailer hitches for your 2019 Honda CR-V can be pretty easily categorized into hidden and non-hidden groups. I highly recommend going with a hidden-crosstube hitch, especially on a new vehicle like yours, as this is going to create a…

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

Hey Frank! This is a newer product, so there aren't many long-term owner reviews available yet. That said, we have done extensive testing on the Benton MoveHitch #B86VR. A strain gauge was used to measure the forces the carrier experiences during…

view full answer...

Answer 8

Hey Erica, thanks for reaching out! Since your 2026 Honda CR-V is a Hybrid we're a bit limited on the hitch options, and you'll need to get one that does require some fascia cutting. For this, I recommend the etrailer Trailer Hitch Receiver…

view full answer...

Answer 9

Hi Rob, both the etrailer hitch part #e98848 and the EcoHitch part #EH25KR will install and function properly on your 2026 CR-V Hybrid Sport Touring, so you’re not risking choosing a hitch that won’t work. Both hitches use a hidden cross tube and…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Is There Trimming Required to Install Draw Tite Hitch DT79MR

Featured Help Information

Miscellaneous Media

Continue Researching