Replacement Mounting Plate for Kaper II Side Marker Lamp 1A-V-1260AR

Question

Question:

I need the back part for 1a-v-1260ar

asked by: Allen A

0

Expert Reply:

I may have a solution for you, but the 1a-v-1260ar part number you've mentioned corresponds to a Kaper II marker lamp, which is a brand that we do not carry. However, it looks like the Optronics Thinline LED Trailer Fender Light for Trailers Over 80" Wide - 10 Diodes - Amber/Red # MCL65ARB is a similar light and the back mounting plate for that MC65 series light is the Black Molded ABS Mounting Bracket for Thin Line Series Clearance, Side Marker Lights # A65B.

I've linked a photo of the dimensions this mounting plate has for you to compare to what you need.

expert reply by: Erik B

0

dimensions
(click to enlarge)

Answer 1

The Roadmaster Replacement Bracket U Clamp for RM Front Sway Bar 1139-140 #RM-B141 measures 4 inches center of bolt hole to center of bolt hole, 5-1/2 inched end to end, 3 inches top to bottom, 1.975 inches inside, and the bolt hole measures 0.74…

view full answer...

Answer 2

The Roadmaster Bracket for Anti-Sway Bar Split Bushings #RMB140 has mounting holes that are spaced out 3-1/4" center-to-center (see attached). This is designed to be a replacement part for the Roadmaster Front Anti-Sway Bar and Bushing Kit…

view full answer...

Answer 3

Hey Nate, We do not have a 3/4" spindle nut or washer, the smallest option is the 7/8" spindle nut #165931and a 1" washer #SW1000. I cannot find anything smaller. Are you sure the threads on you're spindle are 3/4"? If they…

view full answer...

Answer 4

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 5

Hey Will, thanks for reaching out. What I recommend for replacing your 7-way is the following: - etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector #e99011 Wiring your connections thru the junction box helps keep them…

view full answer...

Answer 6

The cable to operate the release on the Bulldog Gooseneck Coupler part #BD0289340317 is not included because it is not needed. It is only for convenience as you can still operate the coupler lock with just the handle. If you do want to add a cable…

view full answer...

Answer 7

There are five mounting brackets available that fit the Optronics Trailer Clearance Side Marker Light #MC65AB. These three are all black plastic. They are Optronics #A65PBPG, #A65PB and #A65B. The first two come with a single wire, the…

view full answer...

Answer 8

The Plug-In Wiring Harness #3064-P that you referenced is the correct brake controller harness for your 2019 Chevy Silverado 1500 and it is actually a brand new product for this generation of GM trucks (it currently only fits the 2019 model Silverado…

view full answer...

Answer 9

Yes, you can install a fifth wheel hitch on a 2021 GMC Sierra 2500 with Carbon Pro Bed. For this, I recommend the Demco Hijacker Autoslide 5th Wheel Trailer Hitch part #DM8550034 with Demco Hijacker Premier Series Above-Bed Base Rails and Custom…

view full answer...

Answer 10

The Optronics Sealed, Thin Line LED Light #MCL65ARB with a sonically-sealed, waterproof lens in a single-unit housing can be used for both the right or left fender without changing the wires. However, to use the LED trailer light #MCL65ARB, you will…

view full answer...

Answer 11

Yes, the light part #MCL65ARB is the correct replacement for what you sent in a picture of on your horse trailer. The mounting bracket in the picture is the same as the part #A65PB so it's a match.

view full answer...

Answer 12

I have a couple options for you that are going to be a close match to the Peterson Piranha LED Clearance Light #M161R . #MCL65ARB is 3-15/16" long and a 10 diode LED light that is amber on the left and red on the right. This is a surface mount…

view full answer...