Front Mount Hitch Installation with a Western Snow Plow

Question

Question:

Hello, Can this hitch work be installed in addition to a Western Ultra Mount snow plow/mount? I have a 2019 Ford F250XL standard cab 6.2 gas 4x4 8foot long bed pick up and would like to set up a front hitch receiver to hold a lawn fertilizer push spreader in the summer months when snow plow is disconnected for season. Please let me know when you can, I would greatly appreciate it!

asked by: Joe P

0

Expert Reply:

It all depends if the plow on your 2019 Ford F250 uses the mounting locations that the EcoHitch does. The EcoHitch # 306-X7904 will bolt under the frame rails but will sit inside your frame. As long as they don't interfere you will be good to go. Take a look as to how your plow installs and it it leaves the bottom and inside of the frame free, you will be good!

expert reply by: Adam E

0

Answer 1

The TorkLift Hitch Extensions are going to be measured for the extension from hitch pin hole to hitch pin hole. So for the Cannon series which fits a Ford 3" receiver we have the following sizes. 21" #TL46CR 24" #TL66CR 36"…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 4

Hello Mel, great question! Yes, the Torklift tie downs part #TL66FV will fit your 2006 GMC Sierra 2500HD crew cab with the 8 foot bed, provided your truck does not have running boards or cab length boards that extend under the bed, and you are not…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Steve, happy to help! The Victron MultiPlus II #VN43VR you're looking at can replace many of the functions of your Magnum MS2812, but there's an important difference with the AC connections. The #VN43VR has one AC input and two AC…

view full answer...

Answer 10

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 11

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Front Mount Hitch Installation with a Western Snow Plow

Product Page this Question was Asked From

Continue Researching