Availability of U-Bolt that Fits 1-1/2 inch Square Axle

Question

Question:

I would like 1.5 inchx5/16x5inch sq. u-bolts what do I order?

asked by: Robert G

0

Expert Reply:

The closest option we have is the part # SP01-120 which is U-bolt that is 1-1/2 inches wide, has a diameter of 1/2 inch, and has a length of 5 inches.

expert reply by: Jameson C

0

Answer 1

Regardless of the axle diameter, generally most modern double-eye springs are 1-3/4 inches wide. U-bolt plate #115983 works with u-bolts #SP01-120 which have a 1-1/2 inch width to fit around the axle. The u-bolt plate will set below the the leaf…

view full answer...

Answer 2

If the center hole of your U-bolt plate isn't large enough for the nut on your leaf spring to fit flush you would want to drill it out large enough so that it will fit properly.

view full answer...

Answer 3

If what you really need is a new axle you can go to a local trailer shop to you and have them custom order you the exact specs you need for a trailer axle. But to attach springs to your 1-1/2 inch square axle you would want the mount plate part…

view full answer...

Answer 4

Hey Roy, The only U-bolt kit we currently only offer for 1-1/2" square axles is part #CE23102, which only has a 3-3/8" length so it likely wouldn't be the best option for you. Instead you'll want to order the 1-1/2" Square…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Availability of U-Bolt that Fits 1-1/2 inch Square Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching