Can 1 Inch Trailer Hub Bearings Replace 1-1/16 Inch Bearings
Updated 03/22/2020 | Published 03/21/2020
Products Featured in This Question
Question:
Can I put 1 inch bearings and races in a hub that has 1 1/16 bearings
asked by: Todd
Expert Reply:
If your existing hub uses 1-1/16 inch bearings, they will need to be replaced the exact same size bearings and races, # L44649, and # L44610. We also have the complete bearing kit available as part # BK1-150, which includes two 1-1/16 bearings and matching races, as well as a grease seal, cotter pin and EZ Lube spindle washer.
Although one sixteenth of an inch may not seem like much of a difference, no parts are more critical for the dependable performance of your trailer than the bearings, races, and seals, so I can't recommend you use bearings other than the one the hub was designed to use. Doing so could potentially cause damage to your hub, and in turn affect other crucial components on your trailer.
Product Page this Question was Asked From
Replacement Trailer Wheel Bearing - L44649 - Qty 1
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.06 Inch I.D.
- Bearing L44649
- Race L44610
- 3500 lbs Axle
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: trailer hubs and drums
- Search Results: trailer leaf springs
- Search Results: marine bearing grease lubricants sealants adhesives
- Search Results: trailer bearings races seals caps
- Shop: CE Smith Trailer Idler Hub Assembly w/ Case for 3.5K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased
- Shop: etrailer Rust-Resistant 3-Leaf Double Eye Spring for 2K Trailer Axles - 20-3/8" Long - Dacromet
- Shop: Replacement Bearing Kit with Bearings L44649, Races L44610, Seal 10-9 - Fits 1.063" Spindles
- Video: Review of Dexter Trailer Bearings Races Seals Caps - Bearings - DX66ER
- Q&A: Replacement Axle for a 1990 EZ Loader Boat Trailer
- Search Results: trailer jack
- Search Results: trailer hitch lock
- Search Results: boat trailer parts
- Shop: 3-Leaf Slipper Spring for 1,500-lb Trailer Axles - 24-1/4" Long - EMCO
- Shop: 3-Leaf Slipper Spring w/ Radius End for 1,500-lb Trailer Axles - 24-5/8" Long
- Shop: Easy Grease Trailer Idler Hub Assembly for 2K Axles - 5 on 4-1/2 - Galvanized
- Shop: 2-Leaf Slipper Spring w/ Flat End for 1,800-lb Trailer Axles - 30" Long
- Video: In-Depth Review of the etrailer Rust-Resistant 3-Leaf Double Eye Spring for 2K Trailer Axles
- Q&A: Any Leaf Springs Designed for Boat Trailers Used in Salt Water
- Q&A: Which Way Should Bow of Trailer Axle Face When Installed on Trailer
- Q&A: Replacement for 31 Inch Slipper Springs on Small Trailer
- Q&A: Option Because No Trailer Leaf Springs are Long Enough
- Video: Review of the etrailer Rust-Resistant 4-Leaf Double Eye Spring for 5K Trailer Axles
- Video: A Closer Look at the Bronze Bushing
- Video: Nylon Bushing Review
- Q&A: Is The Red "N" Tacky Grease From Lucas Okay to Use on Travel Trailer Wet Bolts?
- Q&A: Trailer Plug is a 4-Way Flat But there are 6 Wires
- Video: Breaking Down the Karrier ST175/80R13 Radial Trailer Tire with 13" Aluminum Wheel
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
on Trailer Bearings Races Seals Caps
