Trailer Hub that Fits 1 inch or 1-1/6 inch Diameter Spindle
Updated 10/16/2018 | Published 10/15/2018
Products Featured in This Question
Question:
Getting ready to replace torsion axle that has metric dimensions. Do they make a race/bearing set with metric race OD and SAE US dimensions on spindle for the hub? Id say 1inch or 1 1/16 inch spindle.
asked by: Leo
Expert Reply:
We have hubs that are designed to fit spindle diameters that you mentioned of 1 inch and 1-1/6 inch. If you have a straight spindle with a 1 inch diameter you'd have a BT8 spindle and the hub part # 8-258BTUC1 that you referenced would fit. If you have a spindle with a straight diameter of 1-1/6 inch then you'd have a BTR spindle and would want a # 8-258-50UC1. The diameter of the spindle where the seal would ride on either would be 1.25 inch.
If you can verify your spindle dimensions and they match either hub I mentioned then either would be a match.
Product Page this Question was Asked From
Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2
- Trailer Hubs and Drums
- Idler Hub
- Standard
- L44643 / L44643
- Standard Grade
- For 2000 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Continue Researching
- Shop: Dexter Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized
- Search Results: trailer leaf springs
- Search Results: leaf spring
- Search Results: 18136 mount bracket
- Search Results: 18136
- Shop: Trailer Hitch
- Shop: Dexter Trailer Idler Hub Assembly for 2,200-lb Axles - 5 on 4-1/2 - Galvanized
- Video: Clean Up Your Trailer Wiring
- Shop: 2-Leaf Slipper Spring w/ Flat End for 1,800-lb Trailer Axles - 30" Long
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Trailer Idler Hub Assembly for 2K Axles - 13" to 15" Wheels - 5 on 4-1/2 - Pre-Greased
- Shop: Trailer Wiring
- Search Results: trailer suspension parts
- Search Results: spring seats trailer suspension parts
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: trailer leaf spring
- Q&A: Replacement Hub for 1989 Ranger Trailer
- Q&A: Can Ball Mount be Used Upside Down to Use in Rise Position
- Video: Installing the Curt T-Connector Vehicle Wiring Harness on a 2020 Mazda CX-9
- Video: Install: Curt Trailer Hitch Receiver on a 2022 Mazda CX-9
- Q&A: Recommended Hitch for a 2023 Mazda CX-9
- Video: Dexter Trailer Idler Hub Assembly for 2,200-lb Axles Review
- Video: Measuring To Choose The Right Trailer Axle
- Q&A: Where to Measure on Trailer Spindles to Determine Replacement Hubs
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Video: Feature Breakdown: 2-Leaf Slipper Spring w/ Flat End for 1,800-lb Trailer Axles
- Video: Let’s Check Out the 4-Leaf Slipper Spring w/ Open Eye End for 4,300-lb Trailer Axles
- Q&A: Replacement Hub w/ a 5 on 4-1/2 Lug Pattern and L44643 Inner and Outer Bearings
- Article: Trailer Maintenance Schedule
on Trailer Hubs and Drums
