How Long is the Mounting Bolt on the Optronics LED Clearance Light # MCL95AB
Updated 04/29/2012 | Published 04/27/2012
Products Featured in This Question
Question:
How long is the bolt on product code: MCL95AB? Are all stud mounts typically the same length? I have a 20 ft boat trailer which currently has stud mount amber running lights on the sides, I just want to make sure these would fit before ordering. Trailer is made by REME. Thanks for your help!
asked by: Ian K
Expert Reply:
The bolt on the back of the clearance light # MCL95AB is approximately 5/8 inches long from the back of the light housing to the end of the bolt. Not all bolts on lights equipped with them are the same length but they are generally within very close proximity, no more than 1/4 inch off, from the lights I have measured. The stud in this light is also the grounding point.
Similar lights, like # MCL13A2B, would mount using 2 screws with gasket # A13G2B. This light has 2 wires so you would need to ground the white one to the trailer frame.
Product Page this Question was Asked From
Optronics LED Clearance or Side Marker Light - Submersible - 3 Diodes - Rectangle - Amber Lens
- Trailer Lights
- Clearance Lights
- Marker
- Rectangle
- Stud Mount
- Submersible Lights
- LED Light
- 2L x 1W Inch
- Amber
- Optronics
more information >
Continue Researching
- Shop: Optronics LED Clearance or Side Marker Light - Submersible - 3 Diodes - Rectangle - Amber Lens
- Q&A: Upgrading Lights on 2000 Tracker PT175 Trailer to LED
- Shop: Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double Eye Springs - 2-1/4" Links
- Q&A: Correct Way to Wire Trailer Breakaway Kit
- Search Results: reflectors
- Search Results: trailer lights
- Search Results: side marker trailer lights
- Video: All You Need to Know About the Optronics Red and Amber Trailer Reflector Kit
- Video: An In-Depth Look at the Optronics Trailer Reflector
- Video: Feature Review Optronics LED Trailer Clearance or Side Marker Light
- Video: In-Depth Review of the Replacement Standard Shackle Link
- Video: Bright Way Trailer Breakaway Kit with Switch Review
- Shop: Dexstar Steel Mini Mod Trailer Wheel - 15" x 6" Rim - 6 on 5-1/2 - Silver Powder Coat
- Shop: 5-Leaf Double-Eye Spring for 6,000-lb Trailer Axles - 25-1/4" Long
- Shop: LED Identification Light Bar for Trailers over 80" Wide - Submersible - 9 Diodes - Red Lens
- Video: Let’s Check Out the CE Smith U-Bolt Kit for Mounting Round Trailer Axles
- Shop: UltraThin ID Light Bar for Trailers over 80" Wide - Submersible - 3 Diodes - Red Lens
- Shop: LED Identification Light for Trailers Over 80" Wide - 3 Diode - Sealed - Rectangular - Red
- Search Results: wiring
- Search Results: wire
- Search Results: leaf spring bushing
- Search Results: led side marker light
- Q&A: What is the Post on the Optronics LED Clearance or Side Marker Light Made From
- Q&A: How to Properly Ground Trailer Marker and Taillights
- Q&A: Does Each Light Need to be Grounded When Wiring Trailer Lights
- Video: Optronics Trailer Lights - Clearance Lights - MCL44AB1 Review
- Article: Trailer Lighting Requirements
- Article: Trailer Wiring Diagrams
- Q&A: Disc Brakes for Boat Trailer With 5-Bolt Brake Flange and 6 on 5-1/2 Bolt Pattern
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
on Trailer Lights
