Mounting a Winch Plate and Front Mount Trailer Hitch on a 2007 Toyota Tundra 2WD

Question

Question:

I want to mount a winch plate on my 2wd 07 Tundra and ensure that the winch plat will mount properly enough to allow a Mile Marker 9500 lbs winch to fit on it without touching the bumper. Will this product work correctly or would something else work better? Regards and thank you.

asked by: Jim I

0

Expert Reply:

I spoke with my contact at Curt and he stated that the Curt Front Mount Trailer Hitch, # 31198, will not sit flush with the bumper on your 2007 Toyota Tundra 2WD, but about 2-3 inches back. We offer the Curt Electric Winch Mount Plate, # C31010, that has three pin holes that will allow you to adjust the distance of the winch plate from the vehicle. The measurement from the furthest pin hole to the mounting plate is 8-1/4 inches. I have attached a picture showing these measurements. This may only give you about 2 inches from the front bumper to the rear of the mounting plate.

I do not know the overall dimensions of your winch, but you can measure from the rear mounting points on the bottom of the winch to the furthest back part of the winch. You will want to use that measurement for the amount of clearance that you will need from your bumper.

I have also included an image of the bolt hole dimensions to see if your winch will fit on this winch plate. We also carry the Front Vehicle Winch Wiring Kit, # BDW20205, and the Trailer and Vehicle Wiring Kit, # BDW20207. Both of these kits will allow you to wire your winch to your vehicle.

Another option that may work for you would be to go with a rear mounted trailer hitch like the Draw-Tite Class IV Trailer Hitch, # 41935. You will have more clearance because the receiver mounts flush with the rear bumper and the indent for the step provides more room behind the winch.

You should not exceed the gross weight rating, GAWR, of your front axle and you should check your owners manual for limitations on towing.

expert reply by: John H

0

click to enlarge

Answer 1

If your 2022 Toyota Tundra does not have tow hooks then don't worry about that part of the instructions. If you had tow hooks they would be removed to install the front mount hitch and then reattached. When installing the front mount hitch you…

view full answer...

Answer 2

I spoke with my contact in Tech Support at Curt Manufacturing, who tells me that they have not tested this hitch on an E-450 Chassis yet. He said that the hitch will fit if the holes closest to the front of the vehicle measure 39.5 inches apart…

view full answer...

Answer 3

Since your 2001 Ford F-350 has the blocker beam (which is what I believe you were referencing when you mentioned extra cowl), you can definitely install the Curt Front Mount Trailer Hitch Receiver #C31014. The 34 inch frame is actually a cab and…

view full answer...

Answer 4

If you cut a hole in the skid plate of your 2019 Toyota Tundra when installing the Curt front hitch #31198 you would not be required to remove the hitch to change the oil. I attached a diagram that shows where to cut the hole for access.

view full answer...

Answer 5

The length from the inside of one mounting bracket to the other is 27" on the Curt Front Mount Trailer Hitch Receiver #31540. Distance from mounting holes center to center is 30" and the mounting plate thickness is 5/16". Refer to the…

view full answer...

Answer 6

The Curt Front Mount Trailer Hitch Receiver #C31077 is the only front mount receiver we carry for your 2020 Nissan NV 3500. This receiver is rated for up to 500lbs of tongue weight, a trailer weight of 5,000lbs and a line pull rating of 9,000lbs.

view full answer...

Answer 7

There is a way to find where the end of the hitch receiver will sit once installed on your 2011 Toyota Tundra, but we have not had a chance to install the Curt Front Mount Hitch, #31198, on a 2011 Toyota Tundra yet, so I do not have a specific…

view full answer...

Answer 8

It doesn't look like the Curt front hitch part #31198 would fit your 2001 LX470. The measurements of this hitch are 38-7/8 inches from side to side, 2 inches from front to back 1-7/8 inches from the mounting flange to the cross tube.

view full answer...

Answer 9

Yes the install of the Curt front hitch part #C31014 on your 2003 Ford F-250 does use the front leaf spring bracket like you mentioned. I attached a picture I took from the install instructions (also linked) that shows how it all goes together.

view full answer...

Answer 10

If you are referring to the draw bars (also called arms) for a set of flat towing base plates that are installed on your 2003 Ford Explorer we do offer these. If you are referring to factory tow hooks these we do not offer and you will need to obtain…

view full answer...

Answer 11

This front-mount hitch receiver, part #31352, is the correct specified part for your 2005 Ford Expedition 4WD. I spoke to my contact at Curt Manufacturing regarding the third mounting hole, which evidently is missing from your Expedition. I am told…

view full answer...

Answer 12

The distance from forward mounting hole down to the top of the receiver tube on the Curt Front Mount Trailer Hitch Receiver #31352 is 4.5".

view full answer...

Mounting a Winch Plate and Front Mount Trailer Hitch on a 2007 Toyota Tundra 2WD

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching