Correct Trailer Hub, Drum and Electric Brakes for 3,500 lb Dexter Axle

Question

Question:

I have a Dexter D28H Hf=77.5 Sc=59.5 Dex#1783115. Its on a 2011 StarCraft ar-one 15rb. I am looking for bearings seals brakes and hubs. number stamped on the axle is 132020649. Thanks

asked by: Dimitri G

0

Expert Reply:

Thank you so much for that information and we have exactly what you needed.

I contacted Dexter and they told me that for your 3,500 lb axle with a #84 spindle you will need the following parts:

- Dexter Trailer Hub and Drum Assembly for 3,500-lb E-Z Lube Axles # 84546UC3-EZ
- Dexter Electric Trailer Brake Assembly - 10" - Left Hand # 23-26
- Dexter Electric Trailer Brake Assembly - 10" - Right Hand # 23-27

These hubs do come with the bearings, races and grease seal: inner bearing # L68149, outer bearing # L44649, inner race # L68111, outer race # L44610, and grease seal 10-19.

These 3,500 lb brake assemblies fit your hubs and come with the necessary mounting bolts and hardware.

I have added links to video reviews for you to check out as well.

expert reply by: Kyle S

0

Answer 1

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

I do have an option for you but hardwired trailer brake controllers aren't ideal for a 2022 GMC Canyon as they will require you to splice into the vehicle and run wires throughout. I highly recommend going with the Curt Echo Wireless Trailer…

view full answer...

Answer 10

Good question, and between the K-Source Snap & Zap and Longview towing mirrors for your 2022 Chevy Colorado, the best option is the Longview, with the correct fit for your '22 Colorado being the following part number: - Longview Custom Towing…

view full answer...

Correct Trailer Hub, Drum and Electric Brakes for 3,500 lb Dexter Axle

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching