Do I Need New Tie-Downs When Upgrading to the TorkLift SuperHitch Magnum on a 2011 Ram 3500

Question

Question:

I have a 2011 ram 3500 with factory hitch and torklift frame mount camper tie downs. I want to upgrade hitch to the tld-1102. Will I need to purchase a different set of rear camper tie downs to work with new hitch?

asked by: Steve M

0

Expert Reply:

Yes, but only the rear set of TorkLift Custom Frame-Mounted Camper Tie-Downs will need to be replaced when upgrading to the TorkLift SuperHitch Magnum Trailer Hitch Receiver part # TLD1102-30 from the factory trailer hitch on your 2011 Ram 3500. The front set of TorkLift Custom Frame-Mounted Camper Tie-Downs are the same so you can keep these installed and then replace the rear set with the TorkLift Custom Frame-Mounted Camper Tie-Downs part # TLR3505.

I have attached an install photo of the TorkLift SuperHitch Magnum for you as well.

expert reply by: Conner L

0

click to enlarge

Answer 1

I have a solution for you, but the TorkLift #TLD3109 are not compatible with with the SuperHitch #TLD1102 since the new SuperHitch's side plates are going to occupy the same spot where those old tie downs were previously installed. For this…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 7

Hey Randy thanks for the information! Here are the parts you'll need to add a brake controller to your 2006 Dodge Ram 1500 with a factory 4-Way connector: Brake Controller and Custom Fit Wiring Harness - Curt TriFlex NEXT item #C43GV 7-Way…

view full answer...

Answer 8

Hey Ronnie! You want the upgraded equalizer to match the existing equalizer measurements so you don't throw off the suspension geometry. The Road Armor #LC53CK is only 6" long making it is a little too short for your setup. The MORryde Shock…

view full answer...

Answer 9

Hey David, we have everything we need to flat tow your 2006 Dodge Ram 1500 4WD but the first thing you need is a base plate kit like the Blue Ox part #BX1988 which I like because in my experience the Blue Ox kits are just really well made and easier…

view full answer...

Answer 10

If your 2006 Dodge Ram 2500 already has the B&W Underbed Kit #BWGNRK1308-5W installed, then the B&W Companion #BWRVK3400-5W is definitely the best option for towing a fifth-wheel trailer. The Companions are considered by many to be the best…

view full answer...

Answer 11

You sure do Greg! Which is why the MORryde X-Factor Crossmember for Standard Frame Hangers item #MR33WR comes with longer suspension bolts. These bolts will replace the ones currently being used on your trailer's spring hangers. The X-Factor…

view full answer...

Answer 12

Hey Jim welcome back. To determine if you need the TorkLift Camper Anchor Relocation Kit item #TLA7004, you'll have to take a measurement. You'll want to measure from the front bumper of your Palomino HS2902 to the center of the rear anchor…

view full answer...

Do I Need New Tie-Downs When Upgrading to the TorkLift SuperHitch Magnum on a 2011 Ram 3500

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching