Adding 3rd Brake Light Wiring for Camper Shell on a 2019 Chevy Silverado 2500HD

Question

Question:

i'm adding a camper shell to my 2019 Chevy Silverado 2500HD and I am needing to know what I need to use for the 3rd brake light. thank you.

asked by: Brad

0

Expert Reply:

To isolate the brake light signal on your 2019 Chevy Silverado 2500HD you just need the Pacer Performance 3rd Brake Light Logic Module # PP20-702. You can use the attached installation instructions for the 3rd brake light on your camper shell.

expert reply by: Jon G

0

click to enlarge

Answer 1

Hey Dan, To wire in a camper shell third brake light you'll need the 3rd Brake Light Logic Module #PP20-702 you were looking at and you'll need to splice into your Sierra's left and right turn signal functions. You'll need to pop the…

view full answer...

Answer 2

Yes Paul, you'll just want the 3rd Brake Light Logic Module #PP20-702. This wiring harness filters out unwanted turn signal input to make sure your 3rd brake light turns on only when brakes are applied.

view full answer...

Answer 3

Hey Jim, The Hopkins Custom Tail Light Wiring Kit for Towed Vehicles #HM56200 doesn't have an extra connector to run up to the third brake light on your Jeep. You would have to splice in the Pacer 3rd Brake Light Module #PP20-702 to your #HM56200…

view full answer...

Answer 4

The factory brake controller port on a 2021 Chevy Silverado 1500 is towards the left side under the dash, just above three other wire harness connections and the lower vent tube for your Silverado's AC system. It will be mounted facing downward…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Adding 3rd Brake Light Wiring for Camper Shell on a 2019 Chevy Silverado 2500HD

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching