Draw-Tite QSP Anti-Rattle, Trailer Hitch Silencer and Cover Not Fitting Curt Trailer Hitch
Updated 04/16/2018 | Published 04/13/2018
Question:
When I try to install the QSP bracket over the collar of my Curt hitch receiver Item # C13100, it does not slide on easily. It only goes on about half way. It seems as though the Curt hitch receiver collar is slightly too large?? a Do you know of this issue? b Can I force it on with out interfering with the functionality of the QSP braket? c Can I modify the QSP bracket to make it fit better? Thank you.
asked by: Keith
Expert Reply:
What is probably happening is that the collar around the receiver opening on the Curt hitch has a very thick powder coat that is preventing the Draw-Tite QSP # 63080 from fitting properly. If you were to sand away some of the powder coat on the collar it would likely fit. That would be easier than trying to modify the QSP.
It goes without saying but make sure that the cam tightening lever on the QSP is open when trying to install it on the hitch.
Product Page this Question was Asked From
Draw-Tite QSP Trailer Hitch Silencer and Cover for 2" Hitch Receivers
- Hitch Anti-Rattle
- Non-Locking Anti-Rattle
- Manufacturer Specific
- Fits 2 Inch Hitch
- Sleeve Style
- Accessory Anti-Rattle
- Draw-Tite
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Shop: Vehicle Tow Bar Wiring
- Video: 2024 Subaru Forester etrailer Trailer Hitch Receiver: Complete Installation
- Video: DIY 2022 Subaru Forester Installation for the Draw-Tite Trailer Hitch Receiver
- Video: Hopkins Plug-In Simple Vehicle Wiring Harness Installation - 2021 Subaru Forester
- Video: Hopkins Plug-In Simple Vehicle Wiring Harness Installation - 2022 Subaru Forester
- Video: Checking Out the Draw-Tite QSP Trailer Hitch Silencer and Cover for 2" Hitch Receivers
- Video: Installation: Curt Trailer Hitch Receiver on a 2024 Subaru Forester
- Video: Set up: Draw-Tite Max-Frame Trailer Hitch Receiver on a 2024 Subaru Forester
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Draw-Tite QSP Trailer Hitch Silencer and Cover for 2" Hitch Receivers
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt LED 4-Way Flat Connector (Vehicle End) Tester
- Shop: Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Article: Anti-Rattle Devices
- Article: The 5 Best Trailer Drop Hitches You Can Buy
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Which Pacbreak Airbag Kit Will Fit My 2023 Chevy 1500 Z71?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Recommended Anti-Rattle Hitch Lock for a 2 Inch Receiver on 2017 Toyota Highlander
- Article: Holiday 2025 | Best Gifts for Towers
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Can Demco Duo be Used with Motorhome that has Air Brakes
- Q&A: How Does Demco Coachlink Get Wired To Air Force One Braking System?
- Q&A: Recommended Slide Out Tray for a Dometic CFX3 75DZ Dual Zone Cooler
- Q&A: What is Correct Gap for SumoSpringsi Kit to Have
- Article: How to Choose the Right Trailer Hitch Class
on Hitch Anti-Rattle
