Jack Recommendation to Replace Shelby Jack 5754A on Trailer

Question

Question:

Hi, looking to replace a jack for a snowmobile trailer. Shelby model # 5754A rest is scratched off. Capacity 850 #’s. Was hoping to just snap ring connect to the old bracket that is welded on. Thanks

asked by: Rick

0

Expert Reply:

We did have a customer come back and say that the Fulton jack part # FTJ120W0301 will attach just fine to the pipe mount on the trailer frame where a Shelby jack just like yours was installed.

expert reply by: Jameson C

0

Answer 1

I have a solution for you, but the bracket height of the Dutton-Lainson Round Trailer Jack #DL22210 has a bracket height of 16-5/8", so it would not be short enough to be used on your trailer. I recommend usinig the Fulton F2 Swing-Up Trailer…

view full answer...

Answer 2

I pulled the Fulton F2 Swing-Up Trailer Jack, part #F1413020134, from our warehouse and took a photo and some measurements for you. This jack has dual 7 inch wheels and features a sidewind handle. The jack has an adjustable mount, and is a bolt-on…

view full answer...

Answer 3

Yes. The bolt patterns that were referred to in the videos are actually the same and in reality the .06" is a negligible difference that falls within a reasonable margin of error; I believe that on the #F1413050334 measurements were performed…

view full answer...

Answer 4

We did have a customer come back and say that the Fulton jack part #FTJ120W0301 will attach just fine to the pipe mount on the trailer frame where a Shelby jack just like yours was installed.

view full answer...

Answer 5

For a replacement brake actuator on your 2000 Prestige Boat Trailer I recommend the following depending on what type of brakes you have: -Dexter DX7.5 Drop-N-Go Brake Actuator - Disc Brakes #099-175-20 -Dexter DX7.5 Drop-N-Go Brake Actuator - Drum…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Jack Recommendation to Replace Shelby Jack 5754A on Trailer

Continue Researching