Replacement Swivel Jack for Shelby 5765A

Question

Question:

Looking for a replacement for a Shelby 5765A-24B Jack

asked by: Alex

0

Expert Reply:

For a trailer jack similar to the Shelby jack you mentioned I recommend the Fulton # FTJ120W0301.

This is a 1,200 pound rated swivel jack with a sidewind handle. It's a weld-on jack with 10 inches of lift.

expert reply by: Charles S

0

Answer 1

When it comes to replacing your Shelby 5854a trailer jack I recommend switching to The Fulton Bolt-Thru Swivel Marine Jack with Dual Wheels - Sidewind - 12 inch Lift - 1,500 pounds #FXPD15L. This jack has a lift capacity of 1,500 pounds, and has a…

view full answer...

Answer 2

We offer weld-on and bolt-on trailer jacks that are similar to the Shelby 5764A jack you wish to replace but the jacks we offer are not exact replacements. We do have a jack that has a mounting plate similar to the Shelby mounting plate., It is part…

view full answer...

Answer 3

I do have an option for you but Shelby is no longer in business and there aren't any direct replacement jacks which use the same mounting bracket. I recommend simply removing the old jack and placing a bolt-on jack either in front of or behind…

view full answer...

Answer 4

We did have a customer come back and say that the Fulton jack part #FTJ120W0301 will attach just fine to the pipe mount on the trailer frame where a Shelby jack just like yours was installed.

view full answer...

Answer 5

Since we do not have a Shelby jack mounting bracket that goes to the discontinued Shelby Jack #5876A8, I have no way to confirm whether or not a Fulton jack will fit it. With that being said, the Fulton Bolt-Thru Swivel Marine Jack #F1411300301 is…

view full answer...

Answer 6

I have an option for you, but since Shelby is out of business you will not be able to purchase another Model 5856A jack. Instead I recommend replacing it with the Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200…

view full answer...

Answer 7

With a weld-on Shelby jack, you will need to replace it since Shelby jacks are no longer in production. I recommend the Fulton Round, Snap-Ring Swivel Marine Jack - Weld On, part #FTJ120W0301. This will use the existing weld-on bracket and collar…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Swivel Jack for Shelby 5765A

Featured Help Information

Miscellaneous Media

Continue Researching