Reese Weight Distribution System Recommendation for 1,050 lbs of Tongue Weight

Question

Question:

Could you please link a comparable Curt hitch

asked by: Todd

0

Expert Reply:

If your loaded tongue weight is 1,050 lbs then the Reese Weight Distribution system part # RP66542 would work well as it has a tongue weight range of 600-1,200 lbs which would work well for you.

The only setup that would be better would be the Strait Line part # RP66084 as it has the same tongue weight range but has a sway control system that stops sway before it starts.

For a 2 inch ball you would want part # A-90 and for a 2-5/16 inch ball # 19286.

expert reply by: Jameson C

0

Todd

10/3/2017

Even though my actual trailer weight will be close to 7k, RP66542 will still be the best option?

Jameson C.

10/3/2017

Picking out a weight distribution system is all about the loaded tongue weight. Even if your total trailer weight is lower the higher tongue weight is the crucial component and why the # RP66542 is the correct kit.

Todd

10/4/2017

Could you please link a comparable Curt hitch

Jameson C.

10/4/2017

Your tongue weight doesn't fit perfectly in the range of any of the Curt kits, but the TruTrack part # C17501 would be the closest. It's range is 1,000 to 1,500 lbs. So your tongue weight would come in at the bottom of that range so the ride might be a tiny bit harsh.

Answer 1

Hey Mike, so a friction sway control unit like the part #83660 can help stop some of the sway that starts from wind or passing semis but if you are experiencing persistent sway once you hit a certain speed that will only be fixed by increasing the…

view full answer...

Answer 2

You sure can! You would just mount either the Curt Friction Sway Control #17200 or Reese Friction Sway Control #83660 to the frame of your Travel Trailer. You will then add the Reese Sway-Control Bracket #RP26003 to your ball mount if you have a…

view full answer...

Answer 3

The Reese Weight Distribution System w Shank - Round Bar part #RE34FR does not utilize friction sway control. It is simply a weight distribution system that will redistribute the weight of your setup with the spring bars which will help to reduce…

view full answer...

Answer 4

Hey there Joe, you are correct, you will need a weight distribution hitch with sway control since your owner's manual (according to my online research) says "If the gross trailer weight is over 2000 lb. (907 kg), a sway control device with…

view full answer...

Answer 5

The #118266 is designed for a 2008 Nissan Pathfinder without a factory trailer connector. The plug for the jumper will be in the location you described, behind the kick panel on the passenger's side. However, since you already have a factory…

view full answer...

Answer 6

Yes, the Reese Friction Sway Control Kit #83660 can be used with the Reese Pro Round Bar Weight Distribution #RE34FR. You may need to move the brackets back on the weight distribution hitch to get the ball for the sway control at its 24" center…

view full answer...

Answer 7

The Reese Pro Round Bar Weight Distribution part #RE34FR only comes with a 2-5/16" hitch ball but you can purchase a 2" and swap it out yourself using the 2" Hitch Ball part #A-90. If you don't have the tools to swap it out just…

view full answer...

Answer 8

That's correct it's not that it can't be used, it's just that using a friction sway control kit #83660 with a tow vehicle that already has electronic sway control would not be nearly as effective as a good weight distribution/sway…

view full answer...

Answer 9

The Reese Weight Distribution Systems like part #RE44FR will allow you to reverse without having to disengage the spring bars. That said, you need to make sure you are doing so at a relatively straight angle meaning you can't put the trailer at…

view full answer...

Answer 10

Here's the story about backing your trailer with a weight distribution system. If you're using a friction sway control like part #83660, you should remove the sway control unless you're backing more or less in a straight line. If…

view full answer...

Answer 11

The parts that you have referenced have been obsoleted by Reese and they were unable to identify what you have. The closest weight distribution system currently produced by Reese is the #RP66542 which is rated at 12,000 lbs GTW and 1,200 lbs TW. The…

view full answer...

Answer 12

The Reese Strait-Line Weight Distribution System #RP66084 referenced in your question does indeed allow you to back up with the trailer attached since its sway control is integrated into the head assembly. There isn't a specific angle measurement…

view full answer...

Reese Weight Distribution System Recommendation for 1,050 lbs of Tongue Weight

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching