Which Vehicles Will the Curt Class IV Trailer Hitch Receiver Fit

Question

Question:

What years, makes, and models will this fit?

asked by: John D

1

Helpful Expert Reply:

The Curt Class IV Trailer Hitch Receiver # 14055 is designed to fit all models of the Ford Van from 2000 to 2003 and the E-150, E-250, and E-350 vans from 2004 to 2014.

expert reply by: Charles S

1

Answer 1

To install all necessary wiring for a 7-pin connector and a brake controller on your 2011 Ford E-350 start with the Curt #C56020 4-pole wiring harness. For installation of this harness, if you don't already have them, you will want a Powerbuilt…

view full answer...

Answer 2

Since your 2011 Ford E-350 does not have the factory towing package you will need to start with adding a 4-way connector. I recommend the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C56020 which will plug into your…

view full answer...

Answer 3

Hey Jay! For a gooseneck hitch you need the B&W Turnoverball #BW94UR. I'm not entirely sure what you have in mind for towing, but you can use this as a standard gooseneck or add the Companion 5th wheel hitch to tow your 5th wheel. If…

view full answer...

Answer 4

We have trailer hitches to fit both Ford E-250s and Ford F-250s however the hitches are different and not interchangeable. You didn't say which vehicle you need a hitch for. If you need one for an E-250 van then I recommend part #75703. Or if you…

view full answer...

Answer 5

The 4-way trailer connector wiring harness I recommend for your 2008 Ford Econoline E-350 Van is the part you reference, part #118551. This custom wiring harness adds a 4-way flat trailer connector at the back of your Ford Van to power your…

view full answer...

Answer 6

If your 2014 Ford E-350 van came with a factory installed 7-Way or 4-Way trailer connector then it will have a port to plug in a brake controller. The harness you will need is #3034-P for Tekonsha brake controllers. I recommend the P2 #90885 because…

view full answer...

Answer 7

Hey Scott! I love the products that you've picked out, but we're going to need to get you setup with a 2" receiver on your 2000 Ford Econoline because the adapter you have for your 1-1/4" adapter is going to already drop the tongue…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Which Vehicles Will the Curt Class IV Trailer Hitch Receiver Fit

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching