Trailer Wiring and Brake Controller Set up For a 2003 Ford Van E350

Question

Question:

Good morning I am trying to upfit my 2003 E350 super duty with a trailer braking system. I want a complete kit with the wiring harness including pigtail and controller. Do you offer something like that? or can you send me something that will work. Thanks.

asked by: Brandon M

0

Expert Reply:

Thanks for your question, Brandon.

We have everything you need. There are two different options depending on what wiring is already on your van.

The first option is if your van already has a 4-flat connector at the rear. If it does, you would need the Universal Installation Kit # ETBC7 to upgrade from a 4-flat to a 7-way. For a brake controller, the easiest option to install would be the Redarc # RED96CR.

If your van does not have any wiring at the rear bumper, then you'll need a few different parts. You would want to pick up the Curt T-Connector # C55344, the Universal Installation Kit # ETBC7, and then the Redarc Tow-Pro Liberty # RED62NR.

The Redarc is a really great controller because it doesn't take up any knee space like a traditional brake controller. It's also incredibly reliable and will automatically calibrate itself once installed. From there, you can fine-tune the settings to your preference using the control knob, which can be mounted almost anywhere in the cab.

I've included a picture below showing what the knob looks like once installed.

What kind of trailer are you planning to tow?

expert reply by: Gwendolyn Y

0

Redarc Knob Installed
(click to enlarge)

Don F.

6/11/2026

I installed one in a 2020 Ford Explorer and it was a very simple procedure as my vehicle had both 4 pin and 7 pin plug ins. I find the actual control knob out of the way and extremely easy to use

D H.

6/11/2026

If they offer the Red Arc Pro Liberty for your vehicle, I can say it worked wonderfully on my 509WHP 2021 Explorer ST. It was very easy and clean to install and quick to calibrate with my camper.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Trailer Wiring and Brake Controller Set up For a 2003 Ford Van E350

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching