Trailer Hitch Receiver Options For a 2013 Ford E-350 Cutaway Chassis

Question

Question:

I have a 2013 ford e350 cut away and am have a hard time finding a fitment. Is it possible to get the measurements for this? The frame is 38-5/8.

asked by: Vincent C

0

Expert Reply:

It sounds like your 2013 Ford E-350 cutaway chassis will need the Curt Trailer Hitch Receiver # 14055. This receiver is specific to fitting the cutaway chassis with the mounting bolt holes 38-5/8" on center. If your holes are not this and the 38-5/8" is the frame width you will need a Universal Receiver # 15901 as there is not a custom fit available. The Receiver # 41547 you found is for a F-Series cutaway chassis and will not fit your E-350.

expert reply by: Bud M

0

Answer 1

I would be happy to help you find the right connector. It is behind the dash at the very top of your console on your 2019 Ford E-350. You will need to pop that panel out and the connector you are looking for will be plugged into the insert. I have…

view full answer...

Answer 2

The distances of the mounting holes for the Curt Trailer Hitch Receiver #14055 are 38-1/4" for the rearmost holes and then 38" for the forwardmost (towards the cab) holes. I have attached a dimensional photo for you to check out. Please…

view full answer...

Answer 3

I checked with Curt and the distance between the vertical mounting flanges of the Curt #C15300 is 33.312 inches.

view full answer...

Answer 4

Ambulances are really pretty hard to fit a hitch too since the ambulance bodies all vary quite a bit and none of our hitch manufacturers have decided to come up with a fit for them. I spoke to my contacts at Curt and Reese and the only styles of…

view full answer...

Answer 5

For your 2014 Ford E-350 cutaway chassis the Curt hitch part #14055 would be an excellent option. I attached a picture that shows it sticks out a decent amount from the rear of the frame as well.

view full answer...

Answer 6

If the utility body on your 2006 Ford E-350 van chassis does not sit any lower relative to the frame than on the regular van models you can install a trailer hitch. For example Curt trailer hitch #14055 will work as long as the bolt holes on the…

view full answer...

Answer 7

If the frame on your RV on a 2019 Ford E350 chassis is between 47" and 71" wide, you can use the Multi-Fit Motor Home Trailer Hitch #82201 to replace the existing hitch. This is an adjustable hitch designed to sit between the frame members…

view full answer...

Answer 8

It sounds like you are talking about the tow package wires under your 1996 Chevy pickup. The orange or red wire is for 12 volt power to the 7-Way trailer connector. It powers 12 volt accessories on the trailer and/or provides a maintenance charge to…

view full answer...

Answer 9

I do have some option for you but there aren't any roof rack options specifically designed for a motorhome that I am aware of. That said, we do have a few options that could work like the Rack'Em Fitz-All Enclosed Trailer Ladder Rack part…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Trailer Hitch Receiver Options For a 2013 Ford E-350 Cutaway Chassis

Products Featured in This Question

Continue Researching