Class 4 Trailer Hitch For A 2008 Ford E350 Cutaway With Enclosed Utility Bed
Updated 11/13/2025 | Published 10/20/2025 >
Products Featured in This Question
Question:
Do you have a class 4 hitch for a 2008 Ford e-350 cutaway van with the enclosed utility bed upfit?
asked by: Daniel
Expert Reply:
Hi Daniel!
We do have a hitch for your 2008 Ford E350 cutaway with an enclosed utility bed, but it may not be a custom fit option. If your bolt holes are 38-5/8 inches from frame to frame and the utility bed doesn't sit lower than the standard bumper would, you can use the Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2" # 14055. This one is custom fit and is a pretty easy install. If the bed sits lower and/or the bolt hole measurement is different, you will have to go with a different option.
For that, I recommend going with the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld On - Class V - 2" # 41990-16. This will fit frames up to 44" wide and the 16" bracket height will give you plenty of room to work with. It will need to be welded on, but it is a very good option.
What are you typically towing?
Product Page this Question was Asked From
etrailer Rubber Hitch Cover for 2" Trailer Hitches - Qty 1
- Hitch Covers
- Misc Covers
- Plain
- Rubber
- Fits 2 Inch Hitch
- Standard
- Square
- etrailer
more information >
Continue Researching
- Search Results: curt trailer hitch
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Suspension Enhancement
- Video: Beginner’s Guide to Installing the Curt Trailer Hitch Receiver on a 2002 Ford Van
- Q&A: Trailer Hitch for 2014 Ford E-350 Cutaway Chassis
- Q&A: Dimensions of Mounting Bolt Holes for the Curt Trailer Hitch 14055
- Shop: Blue Ox Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: TowSmart Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: What are the Differences Between Curt and Draw-Tite Hitches for a 2009 Ford E-250.
- Q&A: Possible Hitch to Fit 2010 Ford E-450 Thor RV Application
- Q&A: What Is Mounting Hole Spacing Dimension for Curt Class IV Hitch # 14055
- Article: Trailer Hitch Installation Tips
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Trailer Wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: trailer wiring
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: trailer tires and wheels
- Article: How to Measure for Trailer Hitch Drop
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Brake Controller


Lazer S.
11/13/2025
Hey Daniel, how did things turn out with the hitch for your E-350 cutaway and utility bed? Did the Curt or Draw-Tite option end up fitting your frame setup? Your update could make it easier for others working with similar vans.