2-1/2 inch Adjustable Ball Mount Recommendation for Use with a Rock Tamer Mudflap System

Question

Question:

Will the 2.5 rock tamer work with a 2.5 6 in weigh safe hitch?

asked by: Will

0

Expert Reply:

Yes, the RockTamers Mudflap part # ERT00110 would be compatible with the The WeightSafe 2-1/2 inch ball mount # WS6-25 that you referenced.

We had a customer come back and tell us that the two products worked well together.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I spoke with my contact at Brophy and she told me the measurement from the center of the pinhole to the nearest edge of the ball mount opposite the hitch ball hole is 2-1/2 inches. I have included a diagram that shows the requested dimensions.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

Hey, Daniel. Thanks for your question. We do have a weight distribution hitch that would work for your trailer and still use chains. That hitch is the Blue Ox SwayPro #BXW0350. The tongue weight rating needed for this system to work is between…

view full answer...

2-1/2 inch Adjustable Ball Mount Recommendation for Use with a Rock Tamer Mudflap System

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching